Publicidad
Idiomas disponibles
Idiomas disponibles
How to use multiple UHF devices
If you use more than 2 UHF devices within one please follow this step to set up:
HOW TO SET UP ON AMPLIFIER/SPEAKER for each device to automatically pair:
-from the rst device, long press the transmitter frequency button
ashing, it means the device is pairing.
If the device is disturbed or has noise interference at this time, this mean that the frequency is already occupied by other devices.
-Turn on the receiver, and the indicator light of the receiver will ash 3 times and then pairing.
-Then short press the frequency button of the headset again to perform frequency pairing (short press the headset frequency button, the
frequency indicator light will ash, and when the indicator light ashes green, it means the pairing is complete).
-After the pairing is completed, short press the Frequency button of the headset to switch to the next frequency point and complete the
re-pairing.
Please repeat the steps again till all the devices have been successfully paired, and they can be used directly next time.
Note: is necessary to follow the steps above to make the headset work.
Indicator lights ash
Match failed. Please turn o the transmitter & receiver, then turn on them simultaneously. The indicator light changes from ashing to green light
after a successful match, then you can use it.
No sound
1. Match failed. Please check the indicator light, the transmitter and the receiver need to rematch if it keeps ashing.
2. The battery may be running out of power. Please fully charge before using.
3. For Canta Tu, speakers and other PA devices, please use the "MIC" socket not "AUX" socket and not suitable for device power is less than 15W.
Faint voice
1. Wrong way to wear. Make sure there is nothing that covers the mic condenser. Keep the mic away from the sound source about 20-25cm.
2. Check the volume settings. You can increase the volume of the transmitter and of the device.
3. The device power is too low (below 100W), such as the Bluetooth speaker with the AUX input.
Noise
1.Please check if there is a strong magnetic eld or sound waves or wireless interference.
2. The microphone didn't wear the windscreen foam. Always use the supplied windscreen foam, which can e ectively minimize wind noise and
vocal plosives.
Howling/whistles
1. Please check the position of the speaker. Do not point the microphone directly at the speaker.
2. Try turning o the reverb/echo and turning down the volume.
Intermittent sound
1. The battery may be running out of power. Please fully charge before using.
2. Please check if there is strong Wi-Fi signal interference around.
CAUTION
1. Do not point the microphone directly at speakers to prevent howling. Use the microphone within narrow spaces, adjust the volume not too
high.
2. For Canta Tu, speakers and other PA devices, please use the "MIC" socket not "AUX" socket. The microphone is not suitable for devices with less
than 15W power.
3. Fully charge the transmitter and receiver before use. Turn o the transmitter and receiver when the microphone is not in use.
4. When adjusting the VOLUME on the headset, pay attention to balance also the Canta tu Machine volume, since if they are both too loud, there is
the risk of whistles.
5. Adjust the volume from minimum level slowly, to avoid any voice distortion and noises
6. This device doesn't support fast charging, always use adaptors not higher than 5V/1A
7. This device CTC16110 can work in the same time and place with other 2 identical microphones (till 3 devices working simultaneously). To make
them work properly, is necessary to follow the frequency set up steps. Each microphone must be settled on a di erent frequency.
The cable has to be checked regularly to verify eventual damages. If it is damaged, please do not use it and replace it.
Recharge the product only using the cable included. Only for indoor use, do not expose to water or rain.
TROUBLESHOOTING
for 3 seconds to switch to di erent frequencies. When the indicator light is
10
Publicidad
