Publicidad
Idiomas disponibles
Idiomas disponibles
KNOW HOW TO USE TOOL
•
Use right tool for job. Do not force tool or attachment
to do a job for which it was not designed.
•
Disconnect tool when changing belt or abrasive disc.
•
Avoid accidental start-up. Make sure that the switch
is in the "OFF" position before plugging in.
•
Do not force tool. It will work most efficiently at the
rate for which it was designed.
•
Keep hands away from moving parts and sanding
surfaces.
•
Never leave tool running unattended. Turn the power off
and do not leave tool until it comes to a complete stop.
•
Do not overreach. Keep proper footing and balance.
•
Never stand on tool. Serious injury could occur if tool
is tipped or if belt or disc are unintentionally contacted.
•
Know your tool. Learn the tool's operation, applica-
tion and specific limitations.
•
Use recommended
accessories (refer to page 11).
Use of improper accessories
may cause risk of
injury to persons.
•
Handle workpiece correctly. Protect hands from pos-
sible injury.
•
Turn machine off if it jams. Belt jams when it digs too
deeply into workpiece. (Motor force keeps it stuck in
the work.)
•
Support workpiece with miter gauge, belt platen,
work stop or work table.
•
Maintain 1/16" m aximum clearance between table and
sanding belt or disc.
CAUTION:
Think safety! Safety is a combination of
operator common sense and alertness at all times
when tool is being used.
WARNING:
Do not attempt to operate tool until it is
completely assembled according to the instructions.
A
Figure 1 - Unpacking
Refer to Figures 2 and 3.
CAUTION:
Do not attempt assembly if parts are miss-
ing. Use operator's manual to order replacement parts.
ATTACH ABRASIVE
DISC TO ALUMINUM
DISC
Refer to Figure 2.
•
Remove dust chute by loosening screws and bolts.
•
Remove the adhesive cover from the back of the
abrasive disc.
•
Center abrasive on aluminum disc and press to paste.
•
Make sure abrasive is pasted evenly on the aluminum
disc.
•
Replace dust chute
ATTACH
DISC TABLE
Refer to Figure 2.
•
Set the disc table at right angle to the aluminum disc
and secure the table position using two knobs and
flat washers. Be sure that the gap between abrasive
disc and disc table is 1/16" o r less.
•
Attach pointers to sides of dust chute using 4-0.7 x
8mm socket head bolts from hardware bag. Adjust
pointers to zero mark on trunnion and tighten bolts.
Aluminum Disc
with Abrasive
Refer to Figure 1.
Check for shipping damage. If damage has occurred, a
claim must be filed with the carrier for fastest action.
Parts which need to be fastened to the unit should be
located and accounted for:
A Disc Table
B Abrasive Disc
C Miter Gauge Assembly
D Belt Table
Parts bag includes: horizontal stop bar, work stop, two
knobs, two pointers, one 10-1.5 x 25mm socket head bolt,
two 4-0.7 x 8mm socket head bolts, one 10mm lock
washer, one 10mm flat washer, one 8mm flat washer, two
6mm flat washers, two 4 mm flat washers, one 8-1.25mm
hex nut, one each 3, 5, 6, and 8mm hex wrenches and
one extra long 4mm hex wrench.
Knob
Flat Washer
/
Pointer
/
Disc Table
Du
Chute
Trunnion
Figure 2 - Secure Disc Table and Aluminum Disc
ATTACH BELT TABLE
Refer to Figure 3, page 4.
•
Attach belt table to left side of belt housing using the
socket head bolt, flat washer and lock washer from
the hardware bag.
•
Set the belt table at right angle to the belt.
•
Be sure that gap between belt table and belt is 1/16"
or less.
3
Publicidad
