Publicidad
Idiomas disponibles
Idiomas disponibles
1.
General information
Read and observe the operating instructions, keep them as a reference for
later and ensure they are accessible at all times.
1.1.
SYMBOLS AND MEANS OF REPRESENTATION
Indicates a hazard which if not avoided may lead to
WARNING
death or serious injury.
i
Indicates useful tips and instructions together with in-
formation for efficient and problem-free operation.
2.
Device overview
A
1 Magnetic base 2 Main beam 3 USB-C charging port with charge status display
4 Spotlight 5 On/Off button
3.
Safety
3.1.
GROUPED SAFETY MESSAGES
3.1.1.
Battery
CAUTION
Leaking electrolyte
Eyes and skin irritation can occur due to leaking, poisonous and corrosive electro-
lytes.
▶ Avoid contact with your eyes and body.
▶ In the event of contact, rinse out the affected area immediately with plenty of
water and consult a doctor.
3.2.
INTENDED USE
Cordless LED pen torch with spotlight and infinitely dimmable main beam and mag-
netic base.
For both industrial and private use.
Dust-proof to IP 30.
3.3.
REASONABLY FORESEEABLE MISUSE
Not suitable for use by children.
Do not use in potentially explosive atmospheres.
Do not expose to strong heat, direct sunlight or open fire.
If the casing is damaged, do not continue to use the work lamp.
Do not open the casing.
Do not replace the light bulb.
4.
Commissioning
4.1.
CHARGING THE BATTERY
i
Fully charge the rechargeable battery before using it for the first time.
ü Torch switched off.
1. Connect torch to socket using USB charging cable and USB power supply unit.
▶ Whilst the torch is being charged, the charge status indicator lights up red.
▶ When charging is complete, the charge status indicator light up continuously
green.
2. Disconnect the lamp from the power supply.
3. Fit the cover for the charging port again.
5.
Operation
Risk group 1 to EN 62471.
WARNING
Risk of blinding and injury to the retina
▶ Never look directly into the light beam.
▶ Do not direct light beam at animals' or people's eyes.
▶ In the event of commercial use, the user must be instructed according to the ac-
cident prevention regulations.
5.1.
SWITCHING THE MAIN AND SPOTLIGHT ON/OFF
1. Press the on/off button.
▶ The spotlight comes on.
2. Press the on/off button again.
▶ The spotlight goes out.
▶ The main beam comes on at the last intensity setting used.
3. Press the On/Off button to switch off the main beam.
5.2.
DIMMING THE MAIN BEAM
1. Switch on the main beam.
2. Keep the on/off button pressed until the desired intensity is reached.
▶ The main beam flashes when the highest or lowest intensity has been
reached.
▶ The light intensity is saved 5 seconds after activation.
5.3.
ATTACHING THE LAMP
The magnetic base will stick to all smooth flat magnetic surfaces.
6.
Storage
Before placing the lamp in storage, fully charge the battery. Recharge the battery
every three months. Store at temperatures between -10°C and +40°C. Do not store in
the vicinity of acidic, aggressive, chemical substances, solvents, humidity and dirt.
7.
Cleaning
Disconnect from the power supply before starting cleaning. Clean with a slightly
damp cloth. Do not use chemical, alcohol-based, abrasive or solvent-based cleaners.
8.
Technical data
Lamp
Illumination
Working life
LED
Colour temperature
CRI
Index of Protection
Ambient temperature range
Battery
Battery
Charging duration
Charger DC charging voltage/current
9.
Recycling and disposal
Torch and rechargeable battery must not be disposed of in domestic waste.
Comply with the national regulations for disposal. Torch and rechargeable
battery must be taken to a suitable collection point.
Main beam
Spotlight
20 – 200 lm
60 lm
2 - 16 h
6 h
COB-LED
SMD-LED
5500 - 6500 K
5500 - 6500 K
80
80
IP 30
IP 30
-10 °C to +40 °C
-10 °C to +40 °C
Li ion 3.7 V, 800 mAh
3 h
5 V / 1 A
www.hoffmann-group.com
de
en
bg
zh
da
fi
fr
it
hr
lt
nl
no
pl
pt
ro
sv
sk
sl
es
cs
hu
5
Publicidad
