Publicidad
Idiomas disponibles
Idiomas disponibles
IMPORTANT
Please read
these
instructions carefully before you start to assemble this greenhouse.
Please
carry
out the
steps
in
the order
set
out
in
these instructions.
Keep these
instructions
in
a
safe
place
for future
reference.
»
Care
and Safety advice
Please
follow
the instructions
as
listed
in
this manual.
Sort the parts and check against the list
of
contents.
For
safety purposes we
strongly recommend that the product will
be
assembled
by at least
two
people.
Some parts have metal edges.
Please be
careful when handling components.
Always wear gloves, shoes and safety goggles during assembly.
Do
not attempt to
assemble the carport
in
windy
or
wet conditions.
Dispose
of
all
plastic bags safely
-
keep
them out of
reach
of
small
children.
Keep
children away from the assembly
area.
Do
not attempt to
assemble the carport
if
you
are
tired,
have
taken drugs,
medications
or alcohol, or
if
you
are
prone to dizzy
spells.
When using
a
stepladder
or
power tools, ensure
that
you
are
follow
the
manufacturer's safety advice.
Do
not climb
or stand on the roof.
Heavy
articles should not
be
leaned against the poles.
Please
consult your
local
authorities if
any
permits
are
required to erect carport.
This
product
is
specifically designed
with
a
minor
slope
of
the roof
in
order to allow
drainage of water flow.
Please
keep
roof
and
gutters
clean
of
snow,
dirt
& leaves.
Heavy
amounts of snow
on
roof
can
damage the carport making it
unsafe
to
stand below or nearby.
This
product
was
designed and produced to
be used
mainly
as
a
carport.
>>
Some parts
of this carport
are
painted.
If
color
was
scratched
during
assembly it
can be
fixed
with the following tints:
Grey
-
RAL
7012
»
Cleaning instructions
When
your carport
needs cleaning,
use
a
mild detergent solution
and rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or others special detergents to clean the panel.
Before
Starting Assembly
This
carport must
be
assembled on
a
solid
base (such
as
concrete or asphalt).
Choose
your
site
carefully before beginning assembly.
Site
surface (mainly below poles)
needs
to
be level.
»You
will
need
L
TO01 -
(supplied)
»
During Assembly
When
encountering the information
icon, please refer
to the relevant
assembly step for additional comments and assistance.
Step
5: It
is
recommended to
place
a
sheet
/
Carton
below the parts to avoid
scratches and peeling
of
paint.
Step 5-6: According to the desired drainage direction,
please select
the preferred
side
to
place
the shorter
legs. Please
verify both
legs
#8002
are
mounting
on
the
same side
Step
7:
At the end
of
all screws
connection to
parts,
tighten
all screws
(including
screws
from previous
steps)
Step
13:
Place
part #7580 underneath
each and every panel
to support the edge
of
the
panels.
Step
18:
Level
the profiles
legs
to the flat
surface, and
then attach plugs and
screws
to the ground.
»
General:
Tighten
all screws
at the end
of
assembly.
500cm
196.9"
297.5cm
206cm
81.1"
263cm
103.5"
210cm
82.7"
337cm
132.9"
218cm
85.8"
Do
not tighten
screws and nuts
(411
& 412)
until completion of assembly
process.
These
2
icons
indicate if screws'tightening
is
required or not.
A
Publicidad
