Bosch GST 700 Professional Manual Original página 15

Parallel guide with circle cutter (accessory)
When working with the parallel guide with circle cutter (20)
(accessory), the workpiece must be no more than 30 mm
thick.
Parallel cuts (see figure F): Loosen the locking screw (19)
and slide the scale on the parallel guide through the guide
(18) in the base plate. Adjust the desired cutting width as a
scale value on the inside edge of the base plate. Retighten
the locking screw (19).
Circular cuts (see figure G): Drill a hole large enough to push
the saw blade through on the cutting line within the circle to
be cut. Machine the drill hole with a router or file so that the
saw blade can lie flush with the cutting line.
Position the locking screw (19) on the other side of the par-
allel guide. Slide the scale on the parallel guide through the
guide (18) into the base plate. Drill a hole in the workpiece
in the middle of the section to be cut out. Insert the centring
tip (21) through the inner opening of the parallel guide and
into the drilled hole. Adjust the radius as a scale value on the
inside edge of the base plate. Retighten the locking screw
(19).
Coolant/lubricant
As the material heats up along the cutting line when cutting
metal, you should apply coolant or lubricant.
Maintenance and Service
Maintenance and Cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Clean the saw blade receptacle regularly. For this, remove
the saw blade from the power tool and lightly tap out the
power tool on a level surface.
If the power tool becomes very dirty, this can lead to serious
faults. For this reason, do not cut materials which generate
large quantities of dust from below or overhead.
In extreme conditions, always use a dust extractor if
u
possible. Blow out ventilation slots frequently and in-
stall a residual current device (RCD) upstream. When
machining metals, conductive dust can settle inside the
power tool, which can affect its protective insulation.
If the dust outlet becomes blocked, switch off the power
tool, disconnect the dust extraction system and remove the
dust and chips.
Apply a drop of oil to the guide roller (10) from time to time.
Check the guide roller (10) regularly. If worn, it must be re-
placed through an authorised Bosch after-sales service
centre.
Bosch Power Tools
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch-pt.com.au
www.bosch-pt.co.nz
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: bsctools@icon.co.za
English | 15
1 609 92A 5B4 | (10.07.2019)