Craftsman SECURITY+ 139.53757 Instrucciones Del Usuario

CRAFTSMAN
INSTALLATION
1. Unplug the motor unit before proceeding.
2. OPEN RECEIVER: Insert a small screwdriver in slot on
receiver front panel as shown. Twist up actuator cover.
3. CONNECT RECEIVER AND MOTOR UNIT: Remove about
1/4" of insulation from each end of the 2-strand bell wire.
Connect one end to the receiver screw terminals (polarity is
NOT required). Route wire along the channels and out the
bottom as shown.
4. Connect the other end of the bell wire to the two motor unit
terminals labeled "2" (white) and "1" (red), "common" and
"command" or the terminals used for the push button control.
5. Use insulated staples to secure bell wire between receiver
and motor unit. Length of bell wire depends on where the
receiver will be installed. Replace actuator cover.
6. Choose a 120Vac polarized outlet for the receiver which is
OUT OF THE REACH OF CHILDREN. Plug receiver into
selected outlet. Return power to the motor unit.
PROGRAMMING THE REMOTE TO THE RECEIVER
With Security#®, the code between the remote control and the
receiver changes with each use, accessing over 100 billion new
codes.
You can activate your motor unit with up to 8 Security*#® remote
controls and one Security%*® Keyless Entry.
1. Remove the front panel of receiver case. Re-connect power
to motor unit.
2. Press and release the "SMART" actuator on the receiver. The
learn indicator light will glow steadily for 30 seconds.
3. Within 30 seconds, press and hold the button on the
hand-held remote that you wish to operate your garage door.
The motor unit will now operate when either the receiver
actuator or the remote control push button is pressed.
Repeat Steps 2 and 3 for each remote control that will be used
to operate the garage door motor unit.
PROGRAMMING THE FINGERPRINT KEYLESS ENTRY
TO THE RECEIVER
NOTE: The unit must have an enrolled user before it can be
programmed to the receiver. Due to the 30 second time interval,
a second person may be needed to press the "SMART"
actuator.
1. Remove the front panel of the receiver case. Press and
release the "SMART" actuator on the receiver. The "SMART"
indicator light will glow steady for 30 seconds.
2. Open the Fingerprint Keyless Entry cover and wait for Ready
LED to light.
3. Within 30 seconds of pressing the "SMART" actuator, slowly
and firmly swipe enrolled finger.
NOTE: The Retry LED will light if another swipe is needed.
4. After a passed swipe the Pass LED will light followed by a lit
Send LED. Programming is complete.
5. if the opener does not operate, press and release the
Resend button at 1 second intervals for up to 5 seconds until
the door moves. Programming is complete.
TO ERASE ALL REMOTE CONTROL CODES
Press and hold the "SMART" actuator on the receiver panel until
the indicator light turns off (about 6 seconds). All transmitter
codes are now erased. Then follow the steps above to
reprogram each remote control.
SECURITY
Universal Receiver
@) Model 139.53757
USER INSTRUCTIONS
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
° Be sure power is NOT connected BEFORE installing the
receiver.
To prevent possible SERIOUS INJURY or DEATH from a
moving gate or garage door:
e Install door control within sight of gate or garage door, out
of reach of children at a minimum height of 5 feet (1.5 m),
and away from all moving parts of gate or door.
e NEVER permit children to operate or play with door control
push buttons or remote control transmitters.
® Activate gate or door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to gate or
door travel.
¢ ALWAYS keep gate or garage door in sight until completely
closed. NEVER permit anyone to cross path of moving gate
or garage door.
NOTICE TO U. S. CONSUMERS:
Some states prohibit the service or repair of garage door motor units
which cannot be made to comply with the safety standards contained
in UL 325 (1988 revision). In order to comply with both the letter and
the spirit of these laws, this universal remote control converter kit
should not be used with any Sears Craftsman® garage door opener
manufactured prior to April 1, 1982.
Power Indicator Light
eT Ty
Terminals
sae
Su —
Actuator Cover
__ Bell Wire
Indicator ot
NL?
Light 2
= OL Connect Bell Wire
aa || To Garage Door
Opener Terminals
"SMART"
Actuator Bell Wire
Fingerprint Keyless
Entry |
|
3-Function . .
Remote Control vniversay Receiver
2S\ Select a
push button
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
To order replacement parts call:
1-800-4-MY-HOME® (1-800-469-4663)