Craftsman 351.225000 Manual Del Operador página 5

A temporary 3-prong to 2-prong grounding adapter (see
Figure 6) is available for connecting plugs to a two pole outlet
if it is properly grounded.
Grounding Lug.
Adapter.-.._%_
3-ProngP_.
_
Make Sure
This Is
Connected
To A Known
Ground
2-Prong
Receptacle
Figure 6 - 2-Prong Receptacle with Adapter
• Do not use a 3-prong to 2-prong grounding adapter unless
permitted by local and national codes and ordinances.
(A 3-prong to 2-prong grounding adapter is not permitted in
Canada.) Where permitted, the rigid green tab or terminal on
the side of the adapter must be securely connected to a
permanent electrical ground such as a properly grounded
water pipe, a properly grounded outlet box or a properly
grounded wire system.
• Many cover plate screws, water pipes and outlet boxes are
not properly grounded. To ensure proper ground, grounding
means must be tested by a qualified electrician.
EXTENSION CORDS
• The use of any extension cord will cause some drop in
voltage and loss of power.
• Wires of the extension cord must be of sufficient size to
carry the current and maintain adequate voltage.
• Use the table to determine the minimum wire size (A.W.G.)
extension cord.
• Use only 3-wire extension cords having 3-prong grounding
type plugs and 3-pole receptacles which accept the tool
plug.
• If the extension cord is worn, cut, or damaged in any way,
replace it immediately.
Extension Cord Length
Wire Size ................................... A.W.G.
Up to 25 ft....................................... 18
25 to 50 ft ....................................... 16
NOTE: Using extension cords over 50 ft. long is not
recommended.
MOTOR
The sander is assembled with motor and wiring installed.
225000 MOTOR SPECIFICATIONS:
Horsepower (Continuous Duty) ....................... 3/4
Voltage ........................................ 120
Amp ........................................... 8.0
Hertz .......................................... 60
Phase ....................................... Single
RPM ......................................... 3450
ELECTRICAL CONNECTIONS
WARNING: All electrical connections must be performed by
a qualified electrician. Make sure tool is off and disconnected
from power source while motor is mounted, connected, recon-
nected or anytime wiring is inspected.
Motor is assembled with approved, 3-conductor cord to be
used at 120 volts.
The power lines are inserted directly onto the switch. The
green ground line must remain securely fastened to the frame
to properly protect against electrical shock. The power supply
to the motor is controlled by a single pole locking rocker
switch.
• Remove the key to prevent unauthorized use.
Refer to Figures 7 - 16.
DESCRIPTION
The Craftsman Belt and Disc Sanders are constructed of
rugged die cast aluminum and cast iron providing stability and
vibration-free operation. The belt and disc are used to sand,
deburr, bevel and grind large workpieces of wood and plastic.
The belt housing can be pivoted from vertical to
horizontal for sanding large, straight workpieces. The idler
drum permits the sanding of contoured shapes and finishes.
The disc can be used to sand or bevel surfaces.
The adjustable miter gauge can be used on both the belt and
disc tables for guiding the workpiece at a desired angle while
sanding. Dust shroud has been designed to function as a
work stop for sanding long pieces on the belt.
SPECIFICATIONS
MODEL 225000
Belt size .................................... 6 x 48"
Belt platen area ............................. 6 x 131/2"
Belt speed ................................ 2400 FPM
Disc diameter .................................... 9"
Disc speed ............................... 3100 RPM
Table dimensions ............................. 7 x 10"
Table tilts ................................... 0 to 45 °
Dust port diameter ................................ 2"
Base dimensions ............................ 12 x 19"
Switch ............................. SP, Locking rocker
Weight ...................................... 88 Ibs
Shipping Weight ............................... 93 Ibs
WARNING: Operation of any power tool can result in foreign
objects being thrown into the eyes, which can result in severe
eye damage. Always wear safety goggles complying with
United States ANSI Z87.1 (shown on package) before com-
mencing power tool operation. Safety goggles are available at
Sears retail stores or catalog.
CAUTION: Always observe following safety precautions.
SAFETY PRECAUTIONS
• Whenever adjusting or replacing any parts on the tool, turn
switch OFF and remove the plug from power source.
• Recheck table knob and bolts. They must be tightened
securely.
• Make sure all guards are properly attached. All guards
should be securely fastened.
• Make sure all moving parts are free and clear of any
interference.
• Make sure all fasteners are tight and have not vibrated loose.
• With power disconnected, test operation by hand for clear-
ance and adjust if necessary.
• Always wear eye protection or face shield.
5