Publicidad
Idiomas disponibles
Idiomas disponibles
TO STOP ENGINE
• To stop engine, release operator pres-
ence controlbar.
TO START ENGINE
NOTE: Due to protective coatingson the
engine, a small amount of smoke may be
present duringthe initial use of the prod-
uct and should be considered normal.
1. To start a cold engine, push primer
three (3) times before trying to start.
Use a firm push.This step is not
usuallynecessary when starting an
engine which has already run for a few
minutes.
2. Hold operator presence controlbar
down to the handle and pull starter
handle quickly.Do not allow starter
rope to snap back.
NOTE: Incoolerweather itmaybe necessary
to repeat primingsteps. In warmer weather
over primingmaycause flooding and engine
will not start. If you do flood engine, wait a
few minutes before attempting to start and
do not repeat primingsteps.
MOWING
TIPS
A CAUTION:
Do not use de-thatcher
blade attachments on your mower. Such
attachments are hazardous, will damage
your mower and could void your warranty.
• Under certain conditions, such as very
tall grass, it may be necessary to raise
the height of cut to reduce pushing
effort and to keep from overloading the
engine and leaving clumps of grass clip-
pings. It may also be necessary to re-
duce ground speed and/or run the lawn
mower over the area a second time.
• For extremely heavy cutting, reduce the
width of cut by overlapping previously
cut path and mow slowly.
• For better grass bagging and most cut-
ting conditions, the engine speed should
be set in the FAST position.
• When using a rear discharge lawn
mower in moist, heavy grass, clumps
of cut grass may not enter the grass
catcher. Reduce ground speed (pushing
speed) and/or run the lawn mower over
the area a second time.
• If a trail of clippings is left on the right
side of a rear discharge mower, mow in
a clockwise direction with a small overlap
to collect the clippings on the next pass.
• Pores in cloth grass catchers can be-
come filled with dirt and dust with use
and catchers will collect less grass. To
prevent this, regularly hose catcher off
with water and let dry before using.
10
• Keep top of engine around starter clear
and clean of grass clippingsand chaff.
This will help engine air flow and extend
engine life.
MULCHING MOWING TIPS
IMPORTANT:
For best performance,
keep mower housing free of built-up
grass and trash. See =CLEANING" in the
Maintenance section of this manual.
• The special mulching blade will recur
the grass clippings many times and
reduce them in size so that as they fall
onto the lawn they will disperse into
the grass and not be noticed. Also, the
mulched grass will biodegrade quickly
to provide nutrients for the lawn. Always
mulch with your highest engine (blade)
speed as this will provide the best recut-
ting action of the blades.
• Avoid cutting your lawn when it is wet.
Wet grass tends to form clumps and
interferes with the mulching action. The
best time to mow your lawn is the early
afternoon. At this time the grass has
dried, yet the newly cut area will not be
exposed to direct sunlight.
• For best results, adjust the lawn mower
cutting height so that the lawn mower
cuts off only the top one-third of the
grass blades. If the lawn is overgrown it
will be necessary to raise the height of
cut to reduce pushing effort and to keep
from overloading the engine and leaving
clumps of mulched grass. For extremely
heavy grass, reduce your width of cut
by overlapping previously cut path and
mow slowly.
1/3
• Certain types of grass and grass
conditions
may require that an area be
mulched a second time to completely
hide the clippings. When doing a sec-
ond cut, mow across (perpendicular) to
the first cut path.
• Change your cutting pattern from week
to week. Mow north to south one week
then change to east to west the next
week. This will help prevent matting and
graining of the lawn..
Publicidad
