Suavinex BS01/1 Manual De Instrucciones página 15

3.2. ASSEMBLING THE TRAY ON THE SCALE
If the measurement is to be taken with babies, follow the steps below to attach the tray (B) to the scale (A):
1.Put the two parts of the tray together by fitting the tabs into the grooves. See FIG.1. It is important that the rotating tabs
on the back are parallel to the parts. See FIG. 2.
2. Once the two parts are assembled, carefully insert the protruding part into the slot in the base. See FIG. 3.
3. Turn the tray and scale (B+A) upside down. The rotating tabs remain in the same direction. See FIG. 3A.
4. Rotate the tabs so that they are positioned horizontally and the tray is securely attached to the scale. See FIG. 4.
5. Make sure the tray is securely attached to the scale.
·IMPORTANT:
-To prevent accidents, make sure the base is securely attached.
-The tray can withstand up to 20 kg.
FIG.1
FIG. 2 FIG. 3
FIG. 3A
3.3. USING THE SCALE (WITH OR WITHOUT THE TRAY) WITHOUT THE APP
Having attached the tray (B) or if measuring directly on the scale (A):
1. Make sure the scale is on a stable, flat surface.
2. Press the "ON/OFF" button to switch on the scale.
3. Once the display shows 0.00, the measurement can be taken.
4. During measuring the weight fluctuates and once the weight has stabilised the measurement will flash and remain
on the screen.
To take another measurement, remove the weight and press the "TARE" button.
· IMPORTANT:
-If the measurement is not established due to excessive movement, it is possible to establish it manually by pressing the
HOLD button (1), as explained in section 3.4.
-If using the tray, it is not possible to take the measurement with the baby standing up.
-The tray can withstand up to 20 kg.
-For correct measurement, it is important for the person being weighed not to touch anything other than the scale so as
not to interfere with accurate weighing.
-Up to 30 kg, the scale measures to two decimal places and the resolution is measured in 10 g increments.
-Above 30 kg, the scale measures to one decimal place and the resolution is measured in 100 g increments.
-Make sure the measurement is in the desired units of measurement (kg, oz, lb, lb:oz).
-The buttons are highly sensitive, so functions/units of measurement may be accidentally activated.
-This scale has an energy-saving mode where, if no activity is registered for 60 seconds, the scale will switch off. To
switch the scale off immediately, press and hold the "ON/OFF" button until the display switches off.
-If the LCD display shows "ERR", take the baby/person off the scale and start a new measurement.
3.4. DISMANTLING THE TRAY
Follow the steps below:
- Rotate the tabs so that they are in the position shown in FIG. 3A.
- Separate the tray (B) from the scale (A) FIG. 3.
3.5. USING THE SCALE (WITH OR WITHOUT THE TRAY) WITH THE APP
In order to use the Smart scale with the Suavinex Link
1. Switch the scale on by pressing the ON/OFF button (A). At that point, the bluetooth icon (4) will start to flash blue.
This means that the device is ready to connect to the Suavinex Link
2. Enable the Bluetooth connection on your smartphone.
3. Open the Suavinex Link App and go to the "devices" tab. All the Suavinex Smart products will appear under this
®
tab. Select the scale.
4. Once the device is connected to the smartphone, the Bluetooth icon will remain on.
3.6. LOCK FUNCTION
The weight can be established in two ways:
· Automatic stabilisation: when measuring a baby or child, it is possible they may move, but thanks to the automatic
locking system, when they are still enough, the weight will remain on the display. You can verify that it has stabilised
when the weight flashes and remains on the display.
· Manual stabilisation/locking: if the baby or child moves too much, there may be problems with the automatic
locking system. You can choose to do this manually by pressing the HOLD button for approximately 1 second. The
FIG. 4
App, follow the steps below:
®
App.
®
EN - 29