Adler europe AD 7860 Manual De Uso página 4

side walls of the device and the wall, furniture or curtains.
15. To avoid the risk of fire or explosion, do not spray the dryer with a spray
16. To prevent the casing parts from melting or catching fire, do not place the dehumidifier in
the vicinity of heating devices.
17. Remove the water that has accumulated in the tank. Accidentally drinking water or using
it for other purposes may make you sick.
Product description: Air Dehumidifier AD7860 – Figure 1 and 2
1. Air outlet
2A. Power on icon
2C. Drying clothes mode icon
2E. Digital humidity value display
3. Switch button
5. Handle
7. Water drain hole (for pipe)
9. The float inside water tank closed by lid
Before first use
1. The device working environment: temperature 5~35°C, the minimum humidity is 70% for Automatic mode and Sleep mode and 20% for
Continuous mode CNT.
2. Keep the device away from direct sunlight. Do not insert fingers or other objects into air outlet (1) or air inlet (6).
3. In the process of use, please close the doors and window to avoid wet air entering and affecting proper dehumidification effect.
4. When the device is used, make sure there are no objects within the area of 50cm.
5. Before use, please ensure that the water tank is placed in the correct position to avoid water following out.
6. Before moving the device, empty the water tank at first.
Usage
1.Turning on the dehumidifier
When the device is powered on for the first time, the screen light up for 1 second, a buzzer beeps, the screen shows "--", and the device is
in stand-by mode.
Press the switch (3), the power on icon (2A) lights up, the digital humidity value display (2E) lights upalso and shows the corresponding
color according to the current environmental humidity:
- red: when room relative humidity is above or equal to 80%,
- green: when room relative humidity is 71-79%,
- blue: when room relative humidity is below or equal 70%.
2.Automatic mode
Press the switch (3) again, the icon (2B) will keep light after flashing 3 seconds, and the display (2E) shows the current environment
humidity value. The device will enter into the automatic mode, the automatic mode icon (2B) lights up and the fan will run at high fan speed
when room humidity higher than 70%. When room humidity is below 70% the device stops to operate.
3.Drying clothes / continuous operation mode CNT
Press the switch (3) again, the icon (2C) will keep light after flashing for 3 seconds, and the display (2E) shows the current environment
humidity value. The device enters CNT mode, the drying clothes / continuous operation mode icon (2C) lights up and the fan will run at high
speed. The mode is suitable for drying clothes up to the moment the water tank is full or for continuous dehumidification scenarios after
assembling the pipe to the water drain hole (7). The device will dehumidify continuously at high fan speed, until the environmental humidity
reaches 20%, then device will stop working.
4.Sleep mode
Press the switch (3) again, the icon (2D) will keep light after flashing for 3 seconds, and the display (2E) shows the current environment
humidity value. The device enters sleep mode, the sleep mode icon (2D) starts to light up, whole display (2E) will be dim to do not impact
sleeping comfort of people in room. In the sleep mode, the device will dehumidify the air automatically according to below rule: the fan will
run at low speed if the room humidity will be above 70%, if it be below 70% then the fan stops work and the process of dehumidification will
be stopped, in order to do not make the air dry in room. The comfort air humidification level for human body is around 70%.
5.Turning off the dehumidifier
Press the switch (3) again, the display (2E) will show "--", the device stops working.
The switch (3) operation order is shown by Figure 3.
2.Control panel
2B. Auto mode icon
2D.Sleep mode icon
2F. Full water tank icon
4.Front cover
6. Air inlet
8. Water tank 1L
10. Pipe for continuous drain (not shown at figures).
4