Progress Lighting P2667 Instrucciones De Ensamblaje

P2667 – Smart Ceiling Fan WIFI Control
A) HANDHELD REMOTE CONTROL SETUP
Install the CR2032, 3V battery included. Remove the battery if not used for long periods of
time to prevent damage to the hand held remote. (Fig. 1)
NOTE: The Remote System is equipped with a learning frequency function that has 65K code
combinations to prevent potential interference from other remote units. The frequency on
your Receiver and Transmitter units have been preset at the factory. We recommend setting
up the frequency while installing the ceiling fan instead of using the initial frequency set by the
factory. The process of changing the frequency is as below. Within 60 seconds of turning the
Receiver AC power ON, press and hold the Transmitter FAN OFF(Stop) button for at least 5
seconds. The light kit will flicker to confirm.
the transmitter has set up. After completion of above operation, you can operate the ceiling
fan and light.
If above set up is not successful, turn off the power to the receiver and repeat the above
actions.
Safety Precautions:
WARNING: Disconnect source of electrical power by removing the fuse or switching off
circuit breakers.
• Do not use with solid state fans.
• Electrical wiring must meet all local and national electrical code requirements.
• Electrical source and fan must be 115/120 volts, 60 Hz. Maximum fan motor amps is 1.5 A.
Maximum light watts is 50W-incandescent, 50VA (LED).
1. RECEIVER INSTALLATION
NOTE: Before the electrical power is disabled for the installation of the receiver, pull chain fan
light kits must be left in the on position and the ceiling fan on the highest speed.
Step 1. Insert Receiver into Hanger Bracket with the flat side of the Receiver facing the
ceiling. (Fig. 2a)
Step 2. Motor to Receiver Electrical Connections: Connect the WHITE wire from the fan to
the WHITE wire marked "TO MOTOR N" from the Receiver. Connect the BLACK wire from
the fan to the BLACK wire marked "TO MOTOR L" from the Receiver. Connect the BLUE wire
from the fan to the BLUE wire marked "For Light" from the Receiver. (Fig. 2b)
Step 3. Receiver to House Supply Wires Electrical Connections: Connect the WHITE wire
(Neutral) from the outlet box to the WHITE wire marked "AC in N" from the receiver. Connect
the BLACK wire (Hot) from the outlet box to the BLACK wire marked "AC in L" from the
receiver. Secure all wire connections with the plastic wire nuts provided. (Fig. 2b)
After all splices are made, check to make sure there are no loose strands. As an additional
precaution we suggest securing the plastic wire connectors to the wires with electrical tape.
2. OPERATING THE HAND-HELD REMOTE CONTROL
1. Light Button:
Press and release the button to turn the light ON or OFF. Press and hold the button to set
the desired light brightness. The light will cycle between bright and dim settings as long as
the button is pressed. The light key has an automatic auto-resume feature that allows the
light to remain at the same brightness as the last time it was turned off.
2. Speed Buttons
Press and release the button for the desired speed.
3. Stop Button
This button stops the fan.
4. Timer Buttons
2H, 4H, 8H timer buttons turn off the fan after 2 hours, 4 hours, and 8 hours
Use the screw provided to install the wall holster on the wall or another convenient location of
your choice.
NOTICE!
Your ceiling fan and light kit assembly must meet the following requirements:
Do Not install this fan with wall solid state speed control or wall light dimmer control.
It will permanently damage the receiver of remote control and cause the fan function failure.
CAUTION:
Ceiling Angle shall Not Exceed 30 Degrees, For Mounting controller. Models UC7308RYF
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
The receiver will learn the same frequency that
Fig.1
Loosen the screw
(do not remove it)
to access battery
compartment.
Battery
CR2032
+
( side faces
outward)
WARNING:
CHEMICAL BURN HAZARD.
KEEP BATTERIES AWAY FROM CHILDREN.
Fig.2a
Fig.2b
High Speed
Medium Speed
Low Speed
Stop
Light
Timer
FCC ID: CHQ7235T4 IC: 2968A-7235T4
This device complies with part 15 of the
FCC rules. Operation is subject to the
following two conditions. (1)This device may
not cause harmful interference and, (2)This
device must accept any interference
received, Including interference that may
cause undesired operation.
93100817_A
Note: Make sure to
install flat side of
receiver facing the
ceiling