Publicidad
Rated Load:
max: 300W
150W
(220-240V/AC)
max: 150W
75W
(110-130V/AC)
FUNCTION: Can identify day and night: The consumer can adjust working state in
different ambient light. It can work in the daytime and at night when it is adjusted on the
"sun" position (max). It can work in the ambient light less than 3LUX when it is adjusted
on the "3" position (min). As for the adjustment pattern, please refer to the testing
pattern. Time-Delay is added continually: When it receives the second induction signals
within the first induction, it will restart to time from the moment.
INSTALLATION ADVICE:
As the detector responds to changes in temperature, avoid the following
situations: • Avoid pointing the detector towards objects with highly reflective surfaces,
such as mirrors etc. • Avoid mounting the detector near heat sources, such as heating
vents, air conditioning units, light etc. • Avoid pointing the detector towards objects that
may move in the wind, such as curtains, tall plants etc.
CONNECTION: Warning. Danger of death through electric shock!
• Switch off the power and unload the transparent cover.
• Connect the power to connection terminal of sensor according to connection-wire
diagram. • Fold the metal spring of the sensor upwards and then put the sensor into
the suitable hole or installation box. Releasing the spring, the sensor will be set in this
installation position. • After finishing installing, turn on the power and then test it.
CONNECTION-WIRE DIAGRAM: (See the right figure)
TEST: • Turn the LUX knob clockwise on the maximum (sun).Turn the TIME knob
anti-clockwise on the minimum (-).
• Switch on the power; the sensor and its connected lamp will have no signal at the
beginning. After Warm-up 30sec, the sensor can start work. If the sensor receives the
induction signal, the lamp will turn on. While there is no another induction signal any
more, the load should stop working within 10sec±3sec and the lamp would turn off.
• Turn LUX knob anti-clockwise on the minimum (moon). If the ambient light is more
than 3LUX, the sensor would not work and the lamp stop working too. If the ambient
light is less than 3LUX (darkness), the sensor would work. Under no induction signal
condition, the sensor should stop working within 10sec±3sec.
Note: when testing in daylight, please turn LUX knob to (SUN) position, otherwise the
sensor lamp could not work!
SOME PROBLEM AND SOLVED WAY:
The load does not work: a. Please check if the connection of power source
Installation Height: 2.2-4m
IP class: IP20
Detection Moving Speed: 0.6-1.5m/s
Protection class against electric shock: II
and load is correct. b. Please check if the load is good.
c. Please check if the settings of working light correspond to ambient light.
The sensitivity is poor: a. Please check if there is any hindrance in front of the detector
to affect it to receive the signals. b. Please check if the ambient temperature is too
high.c. Please check if the induction signal source is in the detection field.
d. Please check if the installation height corresponds to the height required
in the instruction. e. Please check if the moving orientation is correct.
The sensor can not shut off the load automatically: a. Please check if there
is continual signal in the detection field. b. Please check if the time delay is set
to the maximum position c. Please check if the power corresponds to the instruction.
DISPOSAL: The device is marked with the symbol of a crossed-out rubbish container,
in accordance with the European Directive 2012/19/EU on Waste Electrical and
Electronic Equipment (WEEE). Products marked with this symbol should not be recycled
or disposed of with other household waste at the end of their useful life. The user is
obliged to dispose of waste electrical and electronic equipment by delivering it to a
designated point where it is recycled. For information on where and how to dispose of
used electrical and electronic equipment in an environmentally safe manner, the user
should contact the relevant local authority, the waste collection point or the point of
sale where they purchased the equipment.
PL
Czujnik ruchu PIR do zabudowy
Wielofunkcyjny wyłącznik podtynkowy z czujnikiem ruchu wyposażony w detektor
podczerwieni o wysokiej czułości. To urządzenie pozwalające zaoszczędzić energię
elektryczną. Produkt umożliwia automatyczne załączenie obciążenia, po wykryciu
ruchu w polu detekcji, dzięki czujnikowi na podczerwień. Dzięki czujnikowi światła
urządzenie można ustawić tak, aby działało tylko o określonej porze dnia.
INFORMACJE TECHNICZNE:
Napięcie: 110-240 V/AC
Częstotliwość zasilania: 50/60Hz
Światło otoczenia: <3-2000LUX (regulowany)
Opóźnienie czasowe: min.10 s ±3s
maks. 7 min ±2min
Obciążenie znamionowe:
max: 300W
150W
(220-240V/AC)
max: 150W
75W
(110-130V/AC)
CECHY:
- Czujnik oświetlenia w zależności od potrzeby może zostać regulowany: pozycja
SŁOŃCE (max)- praca w dzień i nocy, KSIĘŻYC – praca w nocy przy poziome natężenia
światła rzędu ok. 3LUX.
MCE359
Zakres wykrywania: 360°
Odległość wykrywania: max. 6m
Temperatura pracy: -20/+40°C
Wilgotność pracy: <93% RH
Pobór mocy: około 0,5 W
Wysokość instalacji: 2,2-4m Klasa IP: IP20
Prędkość wykrywania ruchu : 0,6-1,5 m/s
Klasa ochrony przed porażeniem elektr: II
Publicidad
