Bosch GLT 300-40 Professional Manual Original página 5

Entsorgung
Stative, Zubehör und Verpackungen sollen einer umweltge-
rechten Wiederverwertung zugeführt werden.
English
Safety Instructions
Read all safety instructions and general in-
structions enclosed with the tripod and the
worklight being used. Failure to observe the
safety instructions and general instructions
may result in electric shock, fire and/or serious injury.
Keep all the safety instructions and general instructions
for future reference.
Ensure that the tripod has a firm footing. The tripod
u
may tip on an uneven or loose floor if the tripod legs are
not fully folded out or if is overloaded.
Take care if you are transporting the tripod with the
u
worklight already fitted. There is a risk of tipping.
Ensure that all screws and fasteners are always
u
tightened firmly by hand. A tripod that is not secure
could become loose or tip over.
Product Description and
Specifications
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The tripod is exclusively intended for fastening Bosch-cord-
less worklights with a 5/8" thread.
Product Features
The numbering of the product features shown refers to the il-
lustrations of the product on the graphic pages.
(1) Tripod screw
(2) Rotary fixing
(3) Tripod leg fastening screw
(4) Rubber cap
(5) Opening for tripod screw
(6) Cable terminal
Technical Data
Worklight tripod
Article number
Tripod thread
Working height max.
Load capacity max.
Bosch Power Tools
Worklight tripod
Weight approx.
Pack size (length × width ×
height)
Values can vary depending upon the product and are subject to ap-
plication and environmental conditions. For further information
www.bosch-professional.com/wac.
Assembly
Loosen the fastening screw (3) and fully fold out the tripod
legs. Tighten the fastening screw firmly by hand.
Position the tripod on a fixed, level floor so that the middle
column is vertical. Firmly fasten the worklight to the tripod
head using the tripod screw (1).
Loosen the rotary fixings (2) on the telescopic shaft and ex-
tend the tripod to the required working height. Tighten the
rotary fixings firmly by hand.
You can fasten a light cable using the cable clamp (6).
If necessary, you can store the tripod screw (1) in the
opening (5).
Maintenance and Service
Maintenance and Cleaning
Keep the tripod clean so that it can be used properly and
safely.
If the rubber caps (4) on the tripod legs are worn, they can
be replaced.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
GLT 300-40
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
1 600 A02 TU4
M10 You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
cm 300
kg 10.0
English | 5
GLT 300-40
kg 4.0
cm 15.5 × 15.5 × 120
1 609 92A 8MH | (12.06.2023)