Publicidad
• Do not make changes or modifications to the construction! If necessary, contact your supplier or an
authorized service centre for advice and repair.
• The car seat does not replace the baby seat or crib. When the baby does not need sleep, it should be placed
in a suitable baby stroller, seat or crib.
• Do not use the product if you find any missing or damaged parts!
• Do not allow children under 3 years of age to fully assemble the product to avoid access to small and
disassembled parts!
• Do not place additional cords or ties on the product to avoid the risk of suffocation!
• Do not use the stroller on escalator and be careful when getting down or up on the sidewalk.
• Keep the plastic packaging away from children to avoid the risk of suffocation!
• DO NOT store the product in humid places and in direct sunlight!
SEE FIGURE PD.A AND PD.B:
PD-A: 1. Button for folding/unfolding the stroller; 2.Handle; 3.Seat adjustment button; 4. Button to release the seat from
the frame; 5. Accessory basket; 6. Rear wheels; 7. Front wheels; 8.5-point seat belt; 9.Safety board.
PD-B: 1. Frame; 2.Front wheels; 3.Rear wheels; 4.Safety board; 5.Foot cover; 6.Axle
1.UNFOLDING OF THE STROLLER FRAME – FIGURES 1-2: Open the frame by releasing the side safety mechanism
(fold/unfold button) as shown in Figure 1. Pull handle up until tube reaches end position (figure 2). You should hear a
clicking sound when the tube locks into place.
2.INSTALLING THE REAR WHEELS - FIGURES 3-6: Insert washer into axle. Align the rear wheel with the axle stand and
install (Figures 12-13). Align the B-shaped metal bracket with the hole in the axle end and insert it to secure the rear
wheel. Place a decorative tassel on the wheel and press until the wheel locks (figures 14-15). Connect the well assembled
rear brake lever to the rear frame and fix it until you hear a clicking sound (figure 16).
3.INSTALLING THE FRONT WHEELS – FIGURES 7-8: As shown in Figure 8, insert the front wheel into the front frame hole.
Fix it until you hear a "click". To remove the front wheels, press the button and the wheels are removed easily by pulling
out.
4.MOUNTING THE SEAT/BASKET - FIGURES 9-10: Align the seat adapters with the slots on the frame. Install the seat
(Figure 9). You should hear a click when the seat locks into place. To disconnect the seat from the frame, press the bottom
button indicated in Figure 10 and lift the seat up. There is a locking mechanism on the inside of the frame to make the
seat more stable.
5.INSTALLING THE FOOT COVER - FIGURES 11-12: Fasten the foot cover using the push button. To finish fitting the cover,
fasten all buttons above the armrest.
6.ATTACHING THE SAFETY BOARD – FIGURES 13-14: Insert both ends of the safety board into the two side holes of the
frame. Secure the guard until you hear a click. To remove the guard, press the release button on both sides of the frame
and pull at the same time.
7.SEAT CONVERSION - FIGURES 15-16: On both sides of the back of the seat there is a strap system to change the position
of the stroller (from lying to sitting and vice versa). Buckle the straps under the seat to set the stroller to sitting mode.
Unbuckle the straps to switch to sleep mode.
8.SEAT reclination - FIGURES 17-18: To adjust the seat recline angle, press the button on the outside of the seat and
move the backrest up or down.
9.ADJUSTING SEAT TILT - FIGURES 19-20: Press the strap system button on the back of the seat and move it up to adjust
the seat to the seated position. Press the strap system button and move it down to adjust the seat to the horizontal
position.
10.CHANGING THE DIRECTION OF CARRY COT – FIGURES 21-24: To change the direction of the carry cot, press the
buttons on either side of the seat Pull out the carry cot, then turn it over to the desired direction and put it back into the
designated slots.
11.ADJUSTING THE FOOTREST – FIGURE 20-21: To adjust the footrest to the desired position, press simultaneously the
buttons on both sides of the footrest and move it up or down.
12.UNFOLDING CANOPY - FIGURE 27: Open the canopy, stretch it well and push down the side struts.
13.5-POINT SAFETY BELT – FIGURE 28: Follow the steps, described in Figure 28. To attach the belt, insert the two tabs of
the lap belt into the buckle on both sides, should click when properly inserted. The shoulder straps are fitted as the metal
tabs are assembled and inserted into the buckle. The sliding adjusters are fitted and must be carefully adjusted on each
side so that the belt is fastened around your child without causing discomfort. To release the bely, press the buckle
button, and pull to open.
PARTS
ASSEMBLY STEPS AND USE
16
Publicidad
