Publicidad
Idiomas disponibles
Idiomas disponibles
ASSEMBLE
BELT DUST CHUTE
Refer to figure 9, page 10.
• Mount belt dust chute (Key No. 40) to platen using two
washer head screws (Key No. 25).
ASSEMBLE STAND
Refer to Figure 8, page 9.
Install rubber foot (Key No. 4) by pressing onto all four legs
(Key No. 3).
Attach one top frame (Key No. 1) to one pair of legs (Key
No. 3) using carriage bolts and hex nuts (Key Nos. 5 and
6). Repeat for second pair of legs.
Attach one brace (Key No. 2) to each pair of legs using car-
riage bolts and hex nuts.)
Connect the two leg sets with the two remaining top
frames. Make sure that the square
holes in the legs align
with the square holes in the top frame. Also make sure that
the slots on top of the frame members are aligned at each
corner. Secure frames to legs using carriage bolts and hex
nuts.
Attach the two remaining braces by aligning the square
holes in the legs and the braces. Insert carriage bolts and
secure with hex nuts.
Refer to Figures 3, 4, 5, 6, and 8, page 4, 5 and 9.
POWER
SOURCE
WARNING:
Do not connect grinder to the power source until
all assembly steps have been completed.
The motor is designed for operation on the voltage and fre-
quency specified. Normal loads will be handled safely on volt-
ages not more than 10% above or below specified voltage.
Running the unit on voltages which are not within range may
cause overheating and motor burn-out. Heavy loads require
that voltage at motor terminals be no less than the voltage
specified on nameplate.
•
Power supply to the motor is controlled by a single pole
locking rocker switch. Remove the key to prevent unautho-
rized use.
GROUNDING
INSTRUCTIONS
WARNING:
Improper connection of equipment grounding
conductor can result in the risk of electrical shock. Equipment
should be grounded while in use to protect operator from
electrical shock.
• Check with a qualified electrician if grounding instructions
are not understood or if in doubt as to whether the tool is
properly grounded.
• This tool is equipped with an approved 3-conductor cord
rated at 150V and a 3-prong grounding type plug (Figure 3)
for your protection against shock hazards.
• Grounding plug should be plugged directly into a properly
installed and grounded 3-prong grounding-type
receptacle,
as shown (Figure 3).
• Do not remove or alter grounding prong in any manner. In
the event of a malfunction or breakdown, grounding pro-
vides a path of least resistance for electrical shock.
WARNING:
Do not permit fingers to touch the terminals of
plug when installing or removing from outlet.
Properly Grounded Outlet __=_i}
Grounding Prong.
3-Prong Plug __'__
Figure 3 - 3-Prong Receptacle
• Plug must be plugged into matching outlet that is properly
installed and grounded in accordance with all local codes
and ordinances. Do not modify plug provided. If it will not fit
in outlet, have proper outlet installed by a qualified
electrician.
• Inspect tool cords periodically, and if damaged, have
repaired by an authorized service facility.
• Green (or green and yellow) conductor in cord is the
grounding wire. If repair or replacement of the electric cord
or plug is necessary, do not connect the green (or green
and yellow) wire to a live terminal.
• Where a 2-prong wall receptacle is encountered,
it must be
replaced with a properly grounded 3-prong receptacle
installed in accordance with National Electric Code and
local codes and ordinances.
WARNING:
This work should be performed by a qualified
electrician.
A temporary 3-prong to 2-prong grounding adapter (see
Figure 4) is available for connecting plugs to a two pole outlet
if it is properly grounded.
Grounding Lug.
_
Make Sure
..._%_
This Is
Adapter
Connected
3-Prong Plug_
_
To A Known
Ground
2-Prong
Receptacle
Figure 4 - 2-Prong Receptacle with Adapter
• Do not use a 3-prong to 2-prong grounding adapter unless
permitted by local and national codes and ordinances.
(A 3-prong to 2-prong grounding adapter is not permitted in
Canada.) Where permitted, the rigid green tab or terminal on
the side of the adapter must be securely connected to a
permanent electrical ground such as a properly grounded
water pipe, a properly grounded outlet box or a properly
grounded wire system.
• Many cover plate screws, water pipes and outlet boxes are
not properly grounded. To ensure proper ground, grounding
means must be tested by a qualified electrician.
EXTENSION
CORDS
• The use of any extension cord will cause some drop in volt-
age and loss of power.
• Wires of the extension cord must be of sufficient size to
carry the current and maintain adequate voltage.
• Use the table to determine the minimum wire size (A.W.G.)
extension cord.
• Use only 3-wire extension cords having 3-prong grounding
type plugs and 3-pole receptacles which accept the tool
plug.
• If the extension cord is worn, cut, or damaged in any way,
replace it immediately.
4
Publicidad
