Publicidad
Enlaces rápidos
Publicidad
Manuales relacionados para Little Seeds 6849196BRUS
Resumen de contenidos para Little Seeds 6849196BRUS
- Página 1 B346849196BRUS00SW inside for Assembly Manual 012024SW Check us out!
- Página 2 6849196BRUS Piper 6 Drawer Dresser Keep this Assembly Manual for future reference Two Adults recommended for assembly This product is not intended for commercial use Do NOT return this product! For missing or broken parts - Call 1-800-489-3351...
- Página 3 Do NOT return this product! Call us! 1-800-489-3351 Monday-Friday limited warranty valid in the U.S and Canada. Helpful Hints PEOPLE NEEDED FOR ASSEMBLY: 1-2 ESTIMATED ASSEMBLY TIME: 60 MIN - Compression dowels are tapped in with a hammer - Make sure to always face the point on the top of the Cam Lock towards the outer edge - Use all the nails provided for the back panel and spread them out equally - Back Panel must be used to make sure your unit is sturdy...
- Página 4 Before You Start Read through each step carefully and follow the proper order Separate and count all your parts and hardware Give yourself enough room for the assembly process Have the following tools: Flat Head Screwdriver, #2 Phillips Head Screwdriver and Hammer to do so may result in stripping the screw, This Cam Lock Fastening System will be used throughout the assembly process.
- Página 5 Before You Start Please Note: You may need to lightly tap the wood dowels with a hammer into the holes during your assembly process. Insert wood dowel completely into the hole. Not Actual Size Wood Dowel Actual Size Wood Dowel will extend out approximately 3/8”.
- Página 6 Board Not actual size T6849196S010SW T6849196S020SW T6849196S030SW TOP PANEL LEFT SIDE PANEL RIGHT SIDE PANEL T6849196S040SW T6849196S050SW T6849196S060SW BOTTOM PANEL TOP MOLDING PARTITION T6849196S070SW T6849196S080SW T6849196S090SW LEFT SIDE DRAWER (LEFT) DRAWER FACE LEFT SIDE DRAWER (RIGHT)
- Página 7 Board Not actual size T6849196S100SW T6849196S110SW T6849196S120SW RIGHT SIDE DRAWER (LEFT) RIGHT SIDE DRAWER (RIGHT) BACK DRAWER T6849196S130SW T6849196S140SW T6849196S150SW BOTTOM DRAWER DRAWER SUPPORT FRONT MOLDING T6849196S160SW T6849196S170SW BACK PANEL...
- Página 8 Hardware Bag Reference Number: 26849196BRUS0SW Part List Actual Size For any replacement hardware, order part #26849196BRUS0SW TSW0001 TSW0002 CAM BOLT CAM LOCK 15-10 TSW0004 TSW0007 SCREW DOWEL TSW3006 TSW0008 CBS 3.5 x 14 8 X 30 HANDLE SCREW SCREW CBS 4 x 38 TSW0015 NAIL...
- Página 9 Hardware Bag Reference Number: 26849196BRUS0SW Part List Not Actual Size TSW3002 ROUND KNOB x6 SETS x1 SET TSW1004 TSW2004 DRAWER SLIDE ANTI TIPPING KIT 350 MM...
- Página 10 Step 1 Insert cam bolts (A) x 6, cam locks (B) x 8 and wood dowels (C) x 8 to the side panel (2) and side panel (3). B B B li leseedskids.com...
- Página 11 Step 2 Insert cam bolts (A) x 2, cam locks (B) x 5 and wood dowels (C) x 4 to the partition (6). Turn over partition (6), then insert cam bolts (A) x 2 on the left face. “Right Face” B B B B “Le�...
- Página 12 Step 3 Attach drawer slides (J) CR x 3 to right side Attach drawer slides (J) CL x 3 to left side panel (3), use screws (D) x 9 to tighten. panel (2), use screws (D) x 9 to tighten. Slide (CL), screw position on panel number 2.
- Página 13 Step 4 Attach drawer slides (J) CR x 3 to left face of partition (6) , use screws (D) x 9 to tighten. Turn over the partition (6), then attach drawer slides (J) CL x 3 to right face of partition (6), use screws (D) x 9 to tighten. “Le�...
- Página 14 Step 5 Insert cam locks (B) x 2 and wood dowels (C) x 2 to front moldings (15) x 4. Insert cam bolt (A) x 1 and cam locks (B) x 2 to top molding (5). * raw edges are shaded li leseedskids.com...
- Página 15 Step 6 Insert cam bolts (A) x 6 to top panel (1). Attach anti tipping kit (I) to top panel (1) and use (Ic) to tighten. “Note : this will be tighten in step 24. ” li leseedskids.com...
- Página 16 Step 7 Attach legs (16) x 5 to bottom panel (4). Tighten the legs clockwise. “Bottom Face” li leseedskids.com...
- Página 17 Step 8 Insert cam bolts (A) x 6 to bottom panel (4). * raw edges are shaded li leseedskids.com...
- Página 18 Step 9 Attach front moldings (15) x 2 to right side Attach front moldings (15) x 2 to left side panel (3). Tighten the cam locks clockwise. panel (2). Tighten the cam locks clockwise. * raw edges are shaded li leseedskids.com...
- Página 19 Step 10 Attach left face of partition (6) to front moldings (15). Tighten the cam locks clockwise. “Le� Face” Pro Tip : Second person is recomended for ease of assembly on this step * raw edges are shaded li leseedskids.com...
- Página 20 Step 11 Attach top molding (5) to left side panel (2) and partition (6). Tighten the cam locks clockwise. “Right Face” Pro Tip : Second person is recomended for ease of assembly on this step * raw edges are shaded li leseedskids.com...
- Página 21 Step 12 Attach right side panel (3) and front moldings (15) to top molding (5) and right face side of panel (6). Tighten the cam locks clockwise. “Right Face” Pro Tip : Second person is recomended for ease of assembly on this step * raw edges are shaded li leseedskids.com...
- Página 22 Step 13 Attach bottom panel (4) to left side panel (2), partition (6) and right side panel (3). Tighten the cam locks clockwise. “Right Face” Pro Tip : Second person is recomended for ease of assembly on this step * raw edges are shaded...
- Página 23 Step 14 With a assistance of second person, carefully turn up right the unit. Attach top panel (1) to left side panel (2), partition (6) and right side panel (3). Tighten the cam locks clockwise. Pro Tip : Second person is recomended for ease of assembly on this step * raw edges are shaded...
- Página 24 Step 15 IMPORTANT ! THE BACK PANEL IS A STRUCTURAL PART OF THIS UNIT AND MUST BE INSTALLED PROPERLY. With the assistance of a second person, carefully lay down the unit face down. Attach back panel (17) with nails (G) x 26. Distance from corner to corner must be equal. Pro Tip : Second person is recomended for ease of assembly on this step * raw edges are shaded...
- Página 25 Step 16 Insert cam bolts (A) x 5 to drawer faces (7). * raw edges are shaded...
- Página 26 Step 17 Insert cam locks (B) x 2 to panels (8), panels (9), panels (10) and panels (11). Insert cam lock (B) x 1 to panels (14). * raw edges are shaded...
- Página 27 Step 18 Attach panel (8), panel (10) and panel (14) to panel (7). Tighten the cam locks clockwise. Attach panel (9), panel (11) and panel (14) to panel (7). Tighten the cam locks clockwise. “Le� Drawer” “Right Drawer” Pro Tip : Second person is recomended for ease of assembly on this step * raw edges are shaded leseedskids.com...
- Página 28 Step 19 Attach panel (13) into the groove of drawer (7) as illustrated x3. “Le� Drawer” “Right Drawer” Pro Tip : Second person is recomended for ease of assembly on this step * raw edges are shaded leseedskids.com...
- Página 29 Step 20 Line up the groove of panel (12) with the panel (13), secure panel using the screws (E) x 5 as illustrated x6. “Le� Drawer” “Right Drawer” Pro Tip : Second person is recomended for ease of assembly on this step * raw edges are shaded leseedskids.com...
- Página 30 Step 21 x3 SETS Attach drawer slides (J) DL to panel (8), use screws (E) x 3 to tighten as illustrated x3. Attach drawer slides (J) DR to panel (10), use screws (E) x 3 to tighten as illustrated x3. Use these holes : Use these holes : (DL)
- Página 31 Step 22 x3 SETS Attach drawer slides (J) DL to panel (9), use screws (E) x 3 to tighten as illustrated x3. Attach drawer slides (J) DR to panel (11), use screws (E) x 3 to tighten as illustrated x3. Use these holes : Use these holes : (DL)
- Página 32 Step 23 Attach handle (H) onto panel (7), secure the handle with screw (F) as illustrated x6. “Le� Drawer” “Right Drawer” * raw edges are shaded leseedskids.com...
- Página 33 Step 24 For Masonry, Concrete, or other wall materials: Consult your local hardware store for appropriate anchors to securely IMPORTANT: THIS UNIT MUST BE SECURE TO THE WALL TO HELP PREVENT TIPOVER. FOLLOW THESE INSTRUCTIONS TO INSTALL THE ANTI-TIPPING SAFETY BRACKET PROVIDED WITH THIS PRODUCT.
- Página 34 Step 25 Carefully insert drawers into the unit as illustrated. Note : Please insert all the drawers into correctly direction by following the draft, interlock system will not function if wrong inserted the drawer. * raw edges are shaded li� leseedskids.com...
- Página 35 Maximum Loads This unit has been designed to support the maximum loads shown. Exceeding these load limits could cause sagging, instability, product collapse, and/or serious injury. 35 lbs. 15.9 kg 75 lbs each drawer 34kg Warning: Risk of serious injury to person - do not place a television on this furniture. This furniture is not approved for use with a television.
- Página 36 Register your product to receive the following: * New trend details -sneak peek on what's new * Surveys -have a voice within our community * Exclusive deals and discount codes * Quick and easy replacement part service To register your product, visit l i l l e s e e d s k i d s .
- Página 37 Español Cubierta Delantera Busque en el interior del manual de montaje Búsquenos! página 2 Conserve este manual de montaje para futuras consultas. Se recomienda dos adultos para el montaje. Este producto no es para uso comercial. No Regrese este producto! Para piezas perdidas o rotas. Visitar: li�leseedskids.com Llamenos al: 1-800-489-3351 (Gra�s) Seguir li�le seeds en...
- Página 38 Español Página 24 Para mampostería, hormigón u otros materiales de pared: Consulte en su ferretería local los anclajes apropiados para sujetar de forma segura el soporte de seguridad. IMPORTANTE: ESTA UNIDAD DEBE ESTAR SEGURA EN LA PARED PARA AYUDAR A PREVENIR AL TIPOVER. SIGA ESTAS INSTRUCCIONES PARA INSTALAR EL SOPORTE DE SEGURIDAD ANTIDISCIPLINADOR PROPORCIONADO CON ESTE PRODUCTO.
- Página 39 Español Página 28 Registre su producto para recibir lo siguiente: * Nuevos detalles sobre las tendencias - Sneek echa un vistazo a lo nuevo * Encuestas - tener una voz dentro de nuestra comunidad * Ofertas exclusivas y códigos de descuento Servicio de piezas de repuesto rápido y fácil Para registrar su producto, visite Ameriwoodhome.com 5 estrellas...
- Página 40 Français Capot Avant Regardez à l’intérieur du manuel d’assemblage Búsquenos! Page 2 Gardez ce manuel d’assemblage pour référence ultérieure. Deux adultes sont recommandés pour l’assemblage. Ce produit n’est pas dest né à un usage commercial. Non Retournez ce produit! Pour les pièces perdues ou cassées. Visiter: li�leseedskids.com Appelez-nous: 1-800-489-3351 (sans frais) Suivre les pe�tes graines sur...
- Página 41 Français page 25 Pour la maçonnerie, le béton ou d’autres matériaux muraux: Consultez votre quincaillier local pour obtenir les ancrages appropriés af n de f xer solidement le support de sécurité. IMPORTANT: CET APPAREIL DOIT ÊTRE SÉCURISÉ AU MUR POUR AIDER À PRÉVENIR TIPOVER. SUIVEZ CES INSTRUCTIONS POUR INSTALLER LE SUPPORT DE SÉCURITÉ...
- Página 42 Français Page 28 Enregistrez votre produit pour recevoir les éléments suivants: * De nouveaux détails sur les tendances - Sneek vérif er la nouvelle * Sondages - ont une voix dans notre communauté t on Service de pièces de rechange rapide et facile Pour enregistrer votre produit, visitez Ameriwoodhome.com 5 étoiles Visitez le site Web de votre distributeur local, classez votre produit acheté...