JBM 53687 Manual De Instrucciones página 5

REF. 53687
(15) into the 12V output socket. The power will be
connected automatically.
NOTE! You can charge the jump starter by connec-
ting it to the car's 12V output socket, with a cord with
cigarette lighter socket adaptors on each end, but
only as a temporary arrangement.
Starting the engine
1. Completely stop the car and turn the jump star-
ter's switch to the "OFF" position.
2. Connect the red clamp to the battery positive
polarity.
3. Connect the black clamp to the vehicle chassis.
NOTE! Do not connect the black clamp into the ne-
gative polarity.
4. Turn the jump starter's switch into the "ON" po-
sition.
5. Turn the vehicle's ignition key to start the engine.
6. Once the engine is working, turn the jump star-
ter's switch into the "OFF" position.
7. Disconnect the red and black clamps.
TECHNICAL SPECIFICATIONS
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Ah Lead-acid battery AGM (1PCS)
Starting current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 750A
Peak current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1500A
Charger (230V/50Hz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V 1A
12V outlets . . . . . . . . . . . . . . . . . . 12V DC output socket (1PCS) (max. 15A current overload protection)
Charging time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 40h
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392x209x370mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9,5kg
PARTS LIST
2
4
3
5
11
1
7
8
9
10
6
13
12
· 5 ·
Emergency light
1. To turn it on, press the LED emergency light bu-
tton (10).
2. To make it flicker as a warning light, press the
LED emergency light button a second time (10).
3. To turn it off, press the LED emergency light but-
ton a third time (10).
Replacing the battery
1. Release all the screws from the rear cover.
2. Separate the front and rear covers; the battery
casing is visible.
3. Remove the battery.
4. Release the positive and negative wires from the
battery.
5. Connect the positive and negative wires co-
rrectly to new battery - the red wire to positive
polarity and the black wire to negative polarity.
6. Place the new battery into unit's casing.
7. Attach the rear cover properly with screws.
NUM DESCRIPTION
1 12V output socket
2 On/Off switch
3 Charging status LED light: Charging
4 Charging status LED light: Charged
5 Nut
6 LED emergency light
7 Warning light
8 Internal battery voltage status
9 Internal battery voltage test button
10 LED emergency light button
11 Charging socket
12 Charger
13 12V cigarette lighter socket adaptor