Publicidad
EN
Installation environment
When installing your product, consider these factors:
•
Electrical: Install electrical wiring carefully. It should be
done by qualifi ed service personnel. Always use a a
12 VDC UL listed Class 2 or CE certifi ed power supply
to power the camera. Do not overload the power cord or
adapter.
•
Ventilation: Ensure that the location planned for the
installation of the camera is well ventilated.
•
Temperature: Do not operate the camera beyond the
specifi ed temperature, humidity, or power source ratings.
The operating temperature of the camera is between -30
to +60°C. Humidity is below 95%.
•
Servicing: Do not attempt to service this camera yourself.
Any attempt to dismantle or remove the covers from this
product will invalidate the warranty and may also result
in serious injury. Refer all servicing to qualifi ed service
personnel.
•
Cleaning: Do not touch the lens with your fi ngers. If
cleaning is necessary, use a clean cloth with some ethanol
and wipe the camera gently.
Unpacking
Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to
use the unit; contact the supplier immediately. If the unit is
returned, it must be shipped back in its original packaging.
Before starting the installation
•
Do not touch the lens by hand as the image may blur.
•
Do not power up the camera until the installation is
completed.
Installing the camera
See pages 2 to 4.
To prevent injury, the camera must be securely attached to the
ceiling/wall in accordance with the installation instructions. The
ceiling or wall must be strong enough to be able to withstand
more than eight times the weight of the camera and its
accessories.
Ensure that the power is disconnected before you wire, install,
or disassemble the camera.
Local storage
The camera includes a pre-installed SD card of 32GB used
for local video storage. The SD card can be replaced and
formatted if needed. The maximum supported SD card
capacity is 256GB. Access recorded video and log fi les via the
web browser.
Setting up the camera
Once the camera is mounted, set up its network and
streaming parameters so that it can be controlled over the
network, and program it as appropriate for its location. Refer
to the camera's confi guration manual for further information,
which is available on our website.
5
Technical specifi cations
Electrical
Voltage input
Power consumption
Miscellaneous
Operating temperature
Relative humidity
IP rating
Dimensions
Weight
Legal information
© 2023 Carrier. All rights reserved. Information is subject to
change without prior notice.
UltraSync names and logos are a product brand of Aritech, a
part of Carrier. Other trade names used in this document may
be trademarks or registered trademarks of the manufacturers
or vendors of the respective products.
While every precaution has been taken during the preparation
of this manual to ensure the accuracy of its contents, Carrier
assumes no responsibility for errors or omissions.
Manufacturer
PLACED ON THE MARKET BY:
Carrier Fire & Security Americas Corporation, Inc.
13995 Pasteur Blvd, Palm Beach Gardens, FL 33418, USA.
Authorized EU manufacturing representative:
Carrier Fire & Security B.V.,
Kelvinstraat 7, 6003 DH Weert, Netherlands.
Product documentation
Please scan the QR code to download the electronic version
of the product documentation. The manuals are available in
several languages.
DE
Installationsumgebung
Beachten Sie beim Installieren des Produkts folgende
Faktoren:
•
Elektrik: Gehen Sie bei der Installation von elektrischen
Leitungen sorgfältig vor. Die Verkabelung sollte von
qualifi zierten Fachkräften durchgeführt werden. Schließen
Sie diese Kamera ausschließlich an ein in der UL-Liste
eingetragenes 12-V-DC-Netzteil der Klasse 2 oder mit CE-
Zulassung an. Schützen Sie Netzkabel oder Adapter vor
12 VDC
12 VDC ± 25%, 0.5 A, max.
6 W, Ø5.5 mm coaxial power plug,
reverse polarity protection
-30 to +60 °C
95% or less non-condensing
IP66
Ø126 × 96 mm
Approx. 590 g
Publicidad
