Publicidad
INSTRUCTIONS FOR THE REMOTE CONTROL
• The remote control uses two AAA batteries, which under
normal conditions will last for about 6 months. Please use two
new batteries of a similar type (pay attention to the poles when
installing).
• When using the remote control, please point the signal emitter
towards the indoor unit receiver; There should be no obstacle
between the remote control and indoor unit.
• Pressing two buttons at the same time will result in a wrong
operation.
• Do not use wireless equipment (such as mobile phones) near
the indoor unit. If any interference occurs because of this,
please switch the unit off, unplug the power cord from the
mains, then plug it again and switch the unit on after a while.
• Do not expose the indoor receiver to direct sunlight, otherwise
it cannot receive the signal from the remote control.
• Do not let the remote control fall to the ground.
• Do not place the remote control under direct sunlight or near
an oven.
• Do not sprinkle water or juice on the remote control. If this
occurs, use a soft cloth to clean it.
• The batteries must be removed from the appliance before it is
scrapped, while ensuring that they are disposed of in a safe way.
EMERGENCY FUNCTIONS
If you cannot find the remote control or if the remote control
batteries are depleted, use the emergency switch.
AIR FLOW SETTING
To turn the airflow function on.
Operation mode
1. When the air conditioner is off
• When the air conditioner is off, press the ' A IR REFRESH'
button, and the air conditioner will turn on. If you press the
'SWEEP' button, the 'HEALTH' function will be activated.
• Pressing the 'HEALTH' button again cancels the function.
• If the 'HEALTH' button is pressed one more time, the air
conditioner will be turned off.
2. When the air conditioner is working in 'HEALTH' mode, if you
press the 'ON/OFF' button, you can change the mode (COOL,
HEAT, etc.) while keeping the 'HEALTH' function active. The air
conditioner will then turn on or off. When the air conditioner is on,
pressing the 'HEALTH' button starts the cooling function.
AIR FLOW SETTING
Horizontal airflow adjustment Use your hands to adjust the air
outlet for setting the flow to the right or left (Fig. 3).
Fig. 3
Caution:
There's a fan inside, don't get your hands on it!
Air outlet
Fig. 4
Vertical airflow adjustment
By repeatedly pressing the 'SWEEP' button on the remote control,
the flaps can be set to a fixed position 1-5 (Fig. 5.6.2). When the
auto swing function is activated in different modes, the flaps swing
repeatedly in the defined range.
ENERGY SAVING SLEEP FUNCTION
1. When the air conditioner is on, press the 'SLEEP' button to enter
'SLEEP' mode on the remote control, and this symbol
appear.
2. If you press the 'SLEEP' button again, the symbol
and the sleep (energy saving) function will be cancelled.
FUNCTION A: In standby mode, the set temperature will increase
after 1 hour of operation in cool and dry mode; and it will decrease
after 1 hour of operation in heating mode. The set temperature will
then be controlled between 16 °C and 32 °C. When the air conditioner
is in SLEEP mode, the indoor fan speed is set to a medium level, but
the user can change the fan speed with the remote control.
FUNCTION B: In standby mode, the set temperature and indoor
fan speed will not change, but the air conditioner display will be off
except for the 'RUNNING' indicator.
ENERGY SAVING
Enter the proper temperature (Do not set the indoor temperature too
low if the room is too cold, as this is harmful to health.)
Avoid direct sunlight (When cooling a room, use a curtain to block
direct sunlight.)
Avoid direct heat sources (When cooling a room, the use of heat
sources can affect the cooling capacity.)
Close doors and windows tightly (Incoming outside air will affect
cooling or heating efficiency)
Air Filter Cleaning (Keeping the air filter clean at all times ensures
high efficiency of the air conditioner operation.)
Good ventilation (Do not place any objects in front of the outdoor
unit' s air inlet and outlet.)
4. TROUBLESHOOTING
THE AIR CONDITIONING IS FAULTY
Check the appliance before sending it for repair.
TYPE OF
CHECKS
FAULT
The air
1. Check if the power is off.
conditioner
2. Check whether the switch is on or whether
does not
the fuse is blown.
work
3. Check the batteries in the remote control.
4. Check whether the entered operating time
has been reached.
5. Check if any working radio equipment works
within 1 meter.
Poor cooling
1. Check if the intake vents are blocked.
or heating
2. Check whether the switch is on or whether
performance
the fuse is blown.
3. Check the batteries in the remote.
4. Check whether the entered operating time
has been reached.
5. Check if any working radio equipment works
within 1 meter.
will
will disappear
7
Publicidad
