Publicidad
Idiomas disponibles
Idiomas disponibles
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
Read Operating Instructions
Please become familiar with all the instructions and
warnings before operating any pneumatic tool.
Always Wear Approved Eye Protection
Impact resistant eye protection should meet or
exceed the standards set forth in ANSI Z87.1,
Occupational and Educational Eye and Face
Protection. Look for marking Z87.1 on your eye
protection to ensure that it is an approved style.
Hearing Protection is Recommended
Hearing protection should be used when the noise
level exposure equals or exceeds an 8 hour time-
weighted average sound level of 85dBA. Process
noise, reflective surfaces, other tools being operated
nearby, all add to the noise level in a given work area.
If you are unable to determine your noise level
exposure, we recommend the use of hearing
protection.
Avoid Prolonged Exposure to Vibration
Pneumatic tools can vibrate during use. Prolonged
exposure to vibration or very repetitive hand and arm
movements, can cause injury. Discontinue the use of
any tool if you experience tingling, numbness, dis-
comfort or pain in your hands or arms. You should
consult your physician before resuming use of tool.
90 PSIG Maximum
This tool is designed to operate at an air pressure of
90 pounds per square inch gauge pressure (90 PSIG)
maximum, at the tool. Use of higher air pressure can,
and may cause injury. Also, the use of higher air
pressure places the internal components under loads
and stresses they were not designed for, causing
premature tool failure.
NOTE: THE AIR SUPPLY SHOULD BE CLEAN AND
DRY, PREFERABLY LUBRICATED. FOR BEST
RESULTS DRAIN THE MOISTURE FROM YOUR
COMPRESSOR DAILY.
Use May Produce Flying Objects
Care should be taken when using any percussion tool.
Keep the point of the chisel in contact with the work
surface. Inspect all accessories carefully for damage
before use. Chisels and chisel retainers should be
kept in good condition and replaced as needed.
Discard any accessory that has been damaged to
prevent anyone from using it.
W W W W W ARRANTY
FULL TWO YEAR WARRANTY ON
CRAFTSMAN AIR-DRIVE TOOLS
If this Craftsman tool fails to give complete satisfaction
within two years from the date of purchase, RETURN IT
TO THE NEAREST SEARS SERVICE CENTER/
DEPARTMENT IN THE UNITED STATES, and Sears will
repair or replace it free of charge. If this Craftsman tool
is used for commercial or rental purposes, this warranty
applies for only 90 days from the date of purchase. This
warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman
Estates, IL 60179.
DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
The Craftsman Model 875.198971 Medium Duty Air
Hammer is designed for chipping, trimming, riveting,
cutting, piercing and peening.
FEATURES & OPERA
FEA
FEA
FEA
FEA
TURES & OPERA
TURES & OPERA
TURES & OPERA
TURES & OPERATION
Features
•
Nylon housing is lightweight and durable for easy
operation.
•
Uses standard .401 inch shank chisels.
•
Alloy steel barrel and heat-treated piston for long
life.
The Craftsman Medium Duty Air Hammer is designed
to operate on 90 PSIG. Lower pressure (below 90
PSIG) will reduce performance of the tool while higher
air pressure (over 90 PSIG) raises the performance of
the tool beyond its rated capacity and could cause
serious damage to tool and user.
Always use clean dry air. Excessive moisture and dirt
will greatly reduce the life of any air tool. We recom-
mend the installation of an in-line filter-regulator-
lubricator as close to the tool as possible.
A 3/8" air hose is required up to a length of 8 ft. If
more length is required a 1/2" air hose should be
connected to the 3/8" hose to ensure the tool has the
necessary air supply. Be sure all hoses and fittings
are the correct size and tightly secured.
Before the tool is connected to the air supply, clear
the air hose of accumulated dust and moisture, and
add 1/4 oz. air tool oil into air tool inlet. Be sure to
lubricate tool daily for best performance.
(2)
ARRANTY
ARRANTY
ARRANTY
ARRANTY
TION
TION
TION
TION
Publicidad
