Publicidad
Idiomas disponibles
Idiomas disponibles
CHARACTERISTICS
▶Power: 1.000 / 2.000W
ES
▶2 levels
▶Fixed position
PT
▶Security grid
FUNCTIONING
▶Before connecting the device to the network, make sure that the
EN
switch is in the "0" position.
▶Plug the power cord into the AC 220-240V~ 50Hz outlet.
▶Through the 2 power system you can start the appliance.
FR
• POSITION 0: OFF position, no button pressed.
• FRESH AIR POSITION: air fan
• POSITION 1: first speed -1,000W
• POSITION 2: second speed - 2,000W
▶If you do not use the appliance for a long time, unplug the power
cord from the electrical outlet.
▶Never try to disassemble the device.
▶If you notice any abnormality (such as unusual noise from the
device), turn off the device and unplug it immediately.
▶Do not use this heater with a programmer, timer or other device that
switches the heater on automatically, as there is a risk of fire if the
heater is covered or incorrectly positioned
▶Make sure that no objects or liquids get inside the appliance through
the openings.
▶The device must only be used in dry environments. Do not use in the
immediate vicinity of a bathtub, shower or swimming pool
▶Protect the device from dust, moisture, sunlight, and direct heat.
LOCATION AND CONNECTION
▶Choose a suitable location for the heater. At least one meter from
any obstruction, walls of flammable materials. Always make sure
that the heater has enough space at the back for such air and at the
front to blow out the hot air (minimum 1 meter).
▶Make sure the heater is always upright on a solid, flat, horizontal,
non-flammable surface.
CONFIGURATION AND OPERATION
▶If the heater is used for the first time (or if you want to maintain
the desired temperature), turn the thermostat dial to the maximum
position (clockwise all the way).
▶With the mode selector, adjust the heater to suit your preferences:
fan only, low power, or high power.
Instruction manual
▶Once the temperature in the area being heated has reached the
Note! After the thermostat has switched off the heating elements,
the fan will continue to spin. This means that air is constantly
moving allowing the heater to accurately detect if the area is
getting colder.
▶The thermostat dial is continuously adjustable. A higher temperature
SAFETY FEATURES
▶In the event of internal overheating, the overheat protection will
CLEANING AND MAINTENANCE
▶Make sure the appliance is unplugged before cleaning it.
▶Clean with a soft damp cloth, without detergent, aggressive liquids
▶Do not immerse the appliance in water or any other liquid.
▶If the appliance is not going to be used for a long period of time,
correct level, slowly turn the thermostat dial counterclockwise until
you hear a soft click, leave the dial in that position. The heater will
automatically maintain the temperature at this level. It does this by
turning the heating elements on and off when the temperature gets
too high or too low.
is set by turning it clockwise; A lower temperature by turning it
counterclockwise.
shut off the heater. If this occurs, immediately turn the mode
selector to or (0), unplug, and allow the heater to cool down for
at least 10 minutes. In theory, the heater can now be used as
normal. Overheating can be caused by the heater not being able to
adequately release its heat or take in fresh air (because the heater
is covered, the grills are blocked, or the heater is too close to a wall,
etc.). Therefore, before using the heater again, remove or adjust
anything that may have caused the appliance to overheat. If you
cannot find the cause and overheating recurs, stop using the heater
and contact your dealer or a certified electrician for inspection/
repair.
or solvents.
protect it and store it, or after cleaning it, in a dry place.
Ref. 07096
Publicidad
