Publicidad
Idiomas disponibles
Idiomas disponibles
3. You receivea 20 oz.containerof oil
with the unit. Slowly pour3/4 (15 oz.)
of the oil from the containerdown the
oil fill spout into the engine.
4. Wait one minuteto allow oil to settle.
Insert and tightendipstick,then re-
move it to check oil level.
5. Continueadding smallamountsof
oil and recheckingthe dipstick until it
readsfull. DO NOT overfill,or engine
will smoke on startup.
6. Always be sure to retightenoil dipstick
beforestartingengine.
• Check
oil level before
each use.
Add oil
if needed.
Fill to full line on dipstick.
• Change
the oil after every 25 hours of
operation
or each season.
You may
need to change
the oil more often under
dusty, dirty conditions.
ADD GASOUNE
• Fill fuel tank.
Use fresh, clean,
regular
unleaded
gasoline
with a minimum
of
87 octane.
Do not mix oil with gasoline.
Purchase
fuel in quantities
that can be
used within 30 days to assure
fuel fresh-
ness.
AI:_WARNmNG:
Experience
indicates
that
alcohol
blended
fuels (called
gasohol
or
using ethanol
or methanol)
can attract
moisture
which
leads to separation
and
formation
of acids during storage.
Acidic
gas can damage
the fuel system
of an
engine
while
in storage.
To avoid engine
problems,
the fuel system
should
be
emptied
before
storage
of 30 days or
longer.
Drain the gas tank, start the
engine
and let it run until the fuel lines
and carburetor
are empty.
Use fresh fuel
next season.
See Storage
Instructions
for
additional
information.
Never use engine
or carburetor
cleaner
products
in the fuel
tank or permanent
damage
may occur.
Al_ CAUTmON:
Fill to bottom
of gas tank
filler neck.
Do not overfill.
Wipe off any
spilled
oil or fuel.
Do not store, spill or use
gasoline
near an open flame.
Gasoline filler cap
Engine oil cap
TO START
ENGINE
1. To start a cold engine,
push primer
three
(3) times
before
trying to start.
Use a firm push.
This step is not
usually
necessary
when
starting
an
engine
which
has already
run for a few
minutes.
2.
Move throttle
control
lever to fast posi-
tion.
3.
Hold upper handle
firmly
and pull
starter
handle
quickly.
Do not allow
starter
rope to snap
back.
TO STOP
ENG(NE
• To stop engine,
move throttle
control
lever to stop position.
NOTE:
In cooler
weather
it may be
necessary
to repeat
priming
steps.
In
warmer
weather
overpriming
may cause
flooding
and engine
will not start.
If you
do flood engine,
wait a few m_
before
Throttle
-'_\
controu
Starter
'_' "_!_!,
//
handle
_,..
/_L
Set the throttle
control
in the fast posi-
tion. If the weeds
or grass are tall and
thick, operate
the trimmer
at a slower
walking
speed.
• Frequently
clean the underside
of the
trimmer
to remove
any grass build up.
Keep top of engine
around
starter
clear
and clean of grass clippings
and chaff.
This will help engine
air flow and extend
engine
life. See "TO REMOVE
ENGINE
COVER"
in the Maintenance
section
of
this manual.
• For best results
and longer
lasting
line, use the ends of the line to do the
cutting.
This is easily
done by moving
slowly
through
very thick and heavy
weeds.
• Use the left side of trimmer
when trim-
ming along fences,
walls, fiowerbeds
and other such objects.
• If trimmer
lines become
too short,
it will
take longer
to complete
the job. If trim-
mer lines are worn to less than half their
original
length,
they should
be replaced.
See "TO REPLACE
TRIMMER
LINE" in
the Maintenance
section
of this manual.
Trimmer
head contact
with concrete,
as-
phalt or other hard surfaces
may cause
premature
wear of the ball on bottom
of
trimmer
head.
Publicidad
