Others; Troubleshooting; Cautions On Use; Maintenance Of Each Part - Pioneer PL-30-K Manual De Instrucciones

03

Troubleshooting

! If your player is not working properly, use the table below for troubleshooting.
If you cannot resolve the problem, please contact our service center or your sales outlet.
Problem Check
The power is not turned on. Is the power cord properly con-
nected?
The turntable does not turn. Is the belt in place?
Has the belt been cut?
No sound or small sound. Are the audio cables properly con-
nected?
Are the terminals and plugs dirty?
Is the headshell attached properly?
The sound is distorted. Is the equalizer switch in its [LINE]
position, even though the player is
connected to your amp's PHONO
terminal?
The sound is extremely Is the equalizer switch in its
quiet. [PHONO] position, even though the
player is connected to your amp's
AUX terminal?
The left and right sound are Are the left and right connections for
reversed. each piece of equipment reversed?
There is a low hum sound Is there an electric device such as a
(humming or buzzing fluorescent lamp or its power cord
sound) during playback. near the connection cord?
The stylus tip does not Is the stylus pressure adjusted
come down on the record. property?
Is the arm horizontally balanced?
Stylus jumping occurs. Is the stylus pressure adjusted
property?
Is the record warped or does it have
scratches?
Does the stylus tip have a lot of dust
on it?
Is anti-skating adjusted correctly?
Is the arm height adjusted correctly?
The arm stops along the Does the record have scratches?
way and does not go ahead.
Is the arm coming into contact with
something?
Sound volume is low or Is the connection to the amplifier
loud. appropriate for the cartridge type
(output)?
Remedy
Properly connect the included power cord to a power
outlet.
Check the belt and rollers. If the belt has slipped off the
turntable, mount it according to the instructions in Assem-
bly. (Page 4 )
Check the belt and roller. If the belt has been cut, replace it
with a new one.
Connect the audio cables properly.
Clean the terminals and plugs before making connections.
Attach the headshell property.
When the player is connected to a PHONO terminal, put
the equalizer switch in the [PHONO] position.
When connected to the AUX terminal, put the equalizer
switch in the [LINE] position. (Be sure to turn the volume
on your amp to its minimum before changing the position
of the equalizer switch.)
Correctly connect the audio cable and the lead wires of
headshell part.
Place the power cord of the fluorescent lamp or other
device as far away as possible.
Match the balance weight to the appropriate stylus pres-
sure value for your cartridge.
Turn the balance weight until the tone arm becomes hori-
zontal state.
Match the balance weight to the appropriate stylus pres-
sure value for your cartridge.
Check the condition of the record.
Remove the shell with cartridge and use a soft tip brush
or writing brush to carefully remove dust, etc. from the
stylus tip.
Adjust anti-skating correctly.
Adjust the arm height correctly.
Check the condition of the record.
Check around the arm. If there is an obstacle, remove it.
Connect the connection cables properly.

Cautions on use

About condensation
Water droplets (condensation) may form inside the unit (on operating parts and lenses) in the winter, for exam-
ple, if the unit is moved from a cold place into a warm room or if the temperature in the room in which the unit
is installed rises suddenly (through heating, etc.). The unit will not operate properly and will not be playable with
condensation inside. Let the unit stand for 1 to 2 hours at room temperature (though this time depends on the
conditions of the condensation) without turning on the power. The water droplets will evaporate and the unit will
become playable. Condensation can occur in the summer as well if the unit is exposed to the direct wind from an
air-conditioner, etc. If this happens, move the unit to a different location.
When transporting the unit to another location
Use the original packing materials to pack the unit.
If the original packing materials are not available, be sure to perform the following.
! Detach the turntable sheet and turntable and pack carefully.
! Detach the headshell and balance weight from the arm and pack carefully.
! Use the arm clamper to secure the tone arm and use tape to secure it so that it does not move.
! Wrap the main unit in a blanket or soft paper so that it will not be damaged.

Maintenance of each part

When attaching and detaching the headshell, turn off the power of the amplifier.
If you attempt to do so while the volume is loud, the speaker could be damaged.
! Remove the shell with cartridge and use a soft tip brush or writing brush to carefully remove dust, etc. from the
stylus tip.
! Use a good quality record cleaner to clean records.
! Use a soft cloth or something similar to clean the headshell terminal and then reattach it to the tone arm.
Cleaning the dust cover, etc.
Use a soft cloth to clean the dust cover and cabinet.
! Do not clean the dust cover while playing. Static electricity could cause the tone arm to be pulled by the dust
cover.

About trademarks and registered trademarks

! Pioneer is a registered trademark of PIONEER CORPORATION.
The names of companies and products mentioned herein are the trademarks of their respective owners.
10

Others