HEIDENHAIN ERN 1120 Instrucciones De Montaje

U = 5 V ± 10 %
P
(I max. 120 mA)
EN 50 178/4.98; 5.2.9.5
IEC 364-4-41: 1992; 411(PELV/SELV)
(siehe, see, voir, vedi, véase
HEIDENHAIN D 231 929)
TTL
0
U , U , U 0
a1 a2 a0
U , U , U , U
a1 a2 a0 aS
0
t
d
|t
d
> 100 mm
Schirm auf Gehäuse
Shield on housing
Blindage sur boîtìer
Schermo sulla carcassa
Blindaje a carcasa
Ø
R 1 R 2
Ø 4.5 mm R 1 ‡ 10 mm R 2 ‡ 50 mm
Ø 8 mm R 1 ‡ 40 mm R 2 ‡ 100 mm
U : Störungssignal
aS
Fault detection signal
Signal de perturbation
Segnale di malfunzionamento
Señal de avería
U = High:
aS
U = Low:
aS
U
360° el.
a1
a
90° el.
U ³ 2.5 V (–I
H
U
a2 U £ 0.5 V (I
L
U
a0
t
d
| £ 50 ns a ³ 0.39 µs
† 100 m (U † 50 m)
aS
> 100 mm > 200 mm
Störquellen
Noise sources
M
Sources parasites
Origine del disturbo
Fuentes de interferencias
(°C
(°F)
T ‡ –30 °C T ‡ –30 °C
(–22 °F) (–22 °F)
–30 ... 80 °C
(–22 ... 176 °F)
0
I
DIN EN 61340 – 5 – 1
DIN EN 61340 – 5 – 2
£ 20 mA)
H
£ 20 mA)
L
DR. JOHANNES HEIDENHAIN GmbH
Dr.-Johannes-Heidenhain-Straße 5
83301 Traunreut, Germany
{ +49 (8669) 31-0
| +49 (8669) 5061
E-Mail: info@heidenhain.de
Technical support
Measuring systems { +49 (8669) 31-3104
E-Mail: service.ms-support@heidenhain.de
TNC support
E-Mail: service.nc-support@heidenhain.de
NC programming
E-Mail: service.nc-pgm@heidenhain.de
PLC programming { +49 (8669) 31-3102
E-Mail: service.plc@heidenhain.de
Lathe controls
E-Mail: service.lathe-support@heidenhain.de
www.heidenhain.de
T ‡ –10 °C
(14 °F)
Ve 00
653 888-91 · 3 · 6/2008 · H · Printed in Germany · Änderungen vorbehalten
Subject to change without notice · Sous réserve de modifications · Con riserva di modifiche · Sujeto a modificaciones
Montageanleitung
Mounting Instructions
Instructions de montage
Istruzioni di montaggio
Instrucciones de montaje
ERN 1120
6/2008
WELLA1: 50C, 50E, 50F
KUPPA1: 14B
ANELA1: 5PS15
BELEA1: C8
| +49 (8669) 32-1000
{ +49 (8669) 31-3101
{ +49 (8669) 31-3103
{ +49 (8669) 31-3105