Thuasne BP 3UG1-3F Manual De Instrucciones página 15

2. Press the M-button to set the month. Press the time button to
confirm and then set the day.
3. Follow the instructions above to set the day, hour and minutes.
4. Once you have set the minutes and pressed the time button, the
date and time are set and the time is displayed.
5. If you want to change the date and time, press and hold the time
button for approx. 3 seconds until the year number starts to
flash. Now you can enter the new values as described above.
Selecting the correct cuff
Thuasne offers different cuff sizes. Select the cuff size to match
the circumference of your upper arms (measured by close fitting in
the centre of the upper arm).
Cuff size
S
M
M - L
L
L - XL
 Pre-shaped cuffs are optionally available.

Only use Thuasne cuffs.
Contact your local Thuasne Service if the enclosed cuff 7 does

not fit.
Connect the cuff to the device by inserting the cuff connector 8

into the cuff socket 5 as far as it will go.
Selecting the user
This device allows to store the results for 2 individual users.
Select the intended user (user 1 or user 2 BK by pressing the Time
button 4.
 Before each measurement, ensure that the correct user is
selected.
3. Taking a blood pressure measurement
Checklist for taking a reliable measurement
1. Avoid activity, eating or smoking immediately before the
measurement.
2. Sit down on a back-supported chair and relax for 5 minutes.
Keep the feet flat on the floor and do not cross your legs.
3. Always measure on the same arm (normally left). It is recom-
mended that doctors perform double arm measurements on a
Thuasne BP 3UG1-3F
for circumference of upper arm
17 - 22 cm
22 - 32 cm
22 - 42 cm
32 - 42 cm
32 - 52 cm
patients first visit in order to determine which arm to measure in
the future. The arm with the higher blood pressure should be
measured.
4. Remove close-fitting garments from the upper arm. To avoid
constriction, shirt sleeves should not be rolled up - they do not
interfere with the cuff if they are laid flat.
5. Always ensure that the correct cuff size is used (marking on the
cuff).
 Fit the cuff closely, but not too tight.
 Make sure that the cuff is positioned 1 - 2 cm above the
elbow.
 The artery mark on the cuff (ca.3 cm long bar) must lie over
the artery which runs down the inner side of the arm.
 Support your arm so it is relaxed.
 Ensure that the cuff is at the same height as your heart.
6. Press the ON/OFF button 1 to start the measurement.
7. The cuff will now pump up automatically. Relax, do not move
and do not tense your arm muscles until the measurement
result is displayed. Breathe normally and do not talk.
8. The cuff fit check AP on the display indicates that the cuff is
perfectly placed. If the icon AP-A appears, the cuff is fitted
suboptimally, but it is still ok to measure.
9. When the correct pressure is reached, the pumping stops and
the pressure falls gradually. If the required pressure was not
reached, the device will automatically pump some more air into
the cuff.
10.During the measurement, the pulse indicator BT flashes in the
display.
11.The result, comprising the systolic AK and the diastolic AL
blood pressure and the pulse rate AM are displayed. Note also
the explanations on further display symbols in this booklet.
12.When the device has finished measuring, remove the cuff.
13.Switch off the device. (The monitor does switch off automati-
cally after approx. 1 min.).
 You can stop the measurement at any time by pressing the
ON/OFF button or open the cuff (e.g. if you feel uneasy or
an unpleasant pressure sensation).
Manual inflation
In case of high systolic blood pressure (e.g. above 135
mmHg), it can be an advantage to set the pressure individually.
Press the ON/OFF button after the monitor has been pumped up
to a level of approx. 30 mmHg (shown on the display). Keep the
EN
13