Publicidad
Idiomas disponibles
Idiomas disponibles
SunPower Reserve
Home energy storage system
NEED MORE HELP?
If you would like to contact us directly, please visit our official website:
https://sunpower.maxeon.com
for more information .
1.0 Transport
There is risk of injury if the battery is lifted incorrectly while being transported as the battery weighs 44 kg .
Transport the battery always as described below .
Handle with care, choose the corresponding handling method according to the weight, and pay attention to
CAUTION
safety .
During transportation, please follow these guidelines:
1 .
The original packaging should be used for transportation .
2 .
During transportation, please keep the packaging away from dangerous sources and take waterproofing measures.
3 .
Secure the packaging during transportation .
2.0 Product Overview
(8) (4)
(5)
(6)
(7)
(4)
610mm
≥300mm
3-6 batteries are suitable for
RESERVE-INV-1-P10-L3-INT
≥300mm
≥300mm
2.3 Scope of Delivery
BATTERY (RESERVE-BAT-1-DC-4-INT)
Battery (x1)
Left Side Plate (x1)
Hexagon Head Screws M5×12
Battery Power Cable 205mm
Grounding Cable 115mm (x1)
(x3)
Silicone Stopper (x9)
Quick Installation Guide (×1)
BATTERY FLOOR MOUNT (SPR-RESERVE-1-DC-4-INT)
Wall Connection Plate of
Wall Connection Plate of
Base Unit (x1)
Base Unit (×1)
Hexagon Head Screws
M5×12 (x8)
Quick Installation Guide
(RESERVE-BAT-1-DC-4-INT)
551942 Revision C - April 2024
212.5mm
Position
Description
1
Battery Start Breaker
(3)
2
Pressure Relief Valve
3
BMS COM (1)
(2)
4
Grounding point
5
Battery+ Power Connector
(1)
6
Battery- Power Connector
7
BMS COM (2) (with terminal
resistor)
250mm
8
Battery LED Display
≥300mm
≥100mm
Lower Left Connection Piece
Lower Right Connection
Right Side Plate (x1)
(×1)
Cable Tie Buckle (x3)
Plastic Blockage (x1)
(x1)
Wall Anchor (×6)
Small Spirit Level (×1)
Battery (×1)
2.1 LED Display
The three LEDs on the front cover provide information about the State of Charge (SOC) or Operating State of the battery .
State of Charge (SoC)
Symbol
Description
White LEDs is flashing
White LED is glowing
LEDs is off
Yellow LED is flashing
Yellow LED is glowing
2.2 Minimum Clearances
For additional batteries, keep a minimum spacing of 300mm .
Local regulations may impact the positioning and mounting of the battery .
CAUTION
CAUTION
≥300mm
Wall Bracket (x1)
Connection Plate between
Wall Brackets of Inverter
and Battery (×2)
2.4 Mounting Location
IP65
Indoor / Outdoor
2.5 Installation
Piece (×1)
2.5.1 Mounting with base
1 .
1
T20
T20
2.5Nm
2.5Nm
3 .
2
SW8
6.0Nm
Description
SOC≤10%
10%<SOC≤30%
30%<SOC≤50%
50%<SOC≤60%
60%<SOC≤90%
90%<SOC≤100%
Operating State Description
Standby: all white LEDs are flashing (0.5s on and 0.5s off)
Normal: white LEDs are glowing or flashing (0.5s on and 1.5s off)
Protection: yellow LEDs are glowing or flashing (0.5s on and 0.5s off)
Error: yellow LEDs are glowing or flashing (0.5s on and 0.5s off)
Shutdown: all LEDs are off
≥300mm
Quantity
Model
2-4 batteries
RESERVE-INV-1-P5-L1-INT
3-6 batteries
RESERVE-INV-1-P10-L3-INT
≥300mm
WALL BRACKET (OPTIONAL)
Connection Plate between
Wall Brackets of Batteries
Flange Nut M5 (×7)
(x2)
Small Spirit Level (×1)
+60°
-10°
90°
44kg
2 .
1
1
SW16
6.0Nm
4 .
2
T20
T20
2.5Nm
2.5Nm
1
Ø10mm
(x2)
≥70mm
≥300mm
≥100mm
Hexagon Head Large
Wall Anchor (×6)
Washer Screw M5×12 (x3)
Maximum altitude:
3000m
6
5
5
3
1
Check horizontal
3
alignment with
spirit level
3
4
3
2
1
2
Remove
Publicidad
