Publicidad
Idiomas disponibles
Idiomas disponibles
① – Base
② – Castors (5 pcs.)
③ – Gas lift
④ – Seat
⑤ – Armrests (left, right)
DESCRIPTION
Intended Purpose. LRG-CHR422XX * is an ergonomic gaming chair on
castors that allows the user to sit and recline comfortably. For household
use.
Design Features. Frame: steel. Seat: 49×53 cm. Backrest: 81×54 cm.
Base: aluminium alloy, Ø 68 cm. Upholstery: stain resistant fabric
(polyester). Filler: cold moulded foam (polyurethane foam). Castors
(Ø 75 mm), armrests: polyurethane. Weight: 25 kg. Head pillow, lumbar
pillow.
Models (colours): LRG-CHR422BL (blue, white); LRG-CHR422BR
(black, red).
Functional Features. Gas lift: class 4; maximum load 150 kg. Adjustable
height: seat – 45.5–53.5 cm from the floor; total height – 124–132 cm.
Rocking mechanism: multiblock, rocking adjustment and lock. Armrests
that adjust in 4 directions. Backrest recline angle: 90–155°.
Operating conditions: temperature 0...+45 °C, relative humidity 45–75 %
(without condensation). Storage conditions: temperature −20...+45 °C,
relative humidity 45–75 % (without condensation).
Carefully unpack all chair parts. Check that all accessories are included
and their quantity (see Figure
Supply" section above).
Wear protective gloves during assembly. Use the hex key (included) to
tighten the screws.
ATTENTION! Do not use mechanical tools (screw gun, electric
screwdriver), do not tighten the screws too much. This can damage the
mounts.
Follow the steps below in sequence (see Figure
ATTENTION! Undo the screws located in the mounting points before
installing the armrests, rocking mechanism and backrest.
1
Insert the castors into the base until they click into place.
2
Place the base with its castors on the floor, insert the gas lift in it.
3
Attach the armrests (left, right) to the seat using the screws. It is
recommended to use a suitable support (for example, the chair box, a
stool).
4
Attach the rocking mechanism to the seat using the screws. Install the
levers on it.
5
Install the seat onto the gas lift by inserting the latter into the hole in
the rocking mechanism as far as it will go.
6
Attach the backrest to the rails on the seat by using the screws.
ATTENTION! Fasten the screws on the left and on the right about
halfway, and then tighten them little by little one at a time so that the
backrest locks directly in the centre of the seat without shifting towards
one of the rails.
7
Fasten the plastic covers onto the backrest rails by using the screws,
and cover the screws with the plugs.
ATTENTION! After two weeks of use, check that all screw connections
are secure.
ADJUSTMENT
Armrests: see Figure
C
on the diagram.
Seat height: press and hold the lever (see Figure
Stay in the chair to lower the seat; stand up from the chair to raise the seat.
Chair rocking: see Figure
E
firmness, lock or control the rocking.
Backrest recline angle: see Figure
ATTENTION! To avoid falling, set the backrest to the reclining position
only if the rocking mechanism has been locked (when the frame was in a
vertical position).
Attach or remove the pillows as desired (see Figure
*
LRG-CHR422XX is the model name. XX is the letter code indicating the colour
of the product.
SCOPE OF SUPPLY (see Figure
⑥ – Rocking mechanism ⑪ – M5×16 screws (2 pcs.)
⑦ – Levers (left, right)
⑧ – Backrest
⑨ – Covers (2 pcs.)
⑩ – Hex key
ASSEMBLY
B
on the diagram and the "Scope of
A
on the diagram).
D
on the diagram).
on the diagram. Turn the lever to adjust the
F
on the diagram.
G
on the diagram).
B
on the diagram)
⑫ – Plugs (2 pcs.)
⑬ – M8×25 screws with washers
(16 pcs., screwed into the seat and backrest)
⑭ – Head pillow
In order to avoid personal injury and damage to the chair, do not:
Use the chair for purposes other than what it is intended for;
Use an unassembled chair or chair with loose parts;
Sit on the edge of the seat or on the armrests;
Stand on the chair;
Sit in a chair with another person;
Lean the entire body only on the backrest of the chair;
Recline in the chair so that the base rests only on two castors;
Place your hands and fingers where the backrest attaches to the seat;
Move abruptly in the chair while adjusting it;
Exceed the permissible load of the chair;
Push on the reclined backrest, push or unscrew the chair when there
is a person in it;
Set the backrest to the reclining position if the rocking mechanism has
not been not locked when the frame was in the vertical position.
Do not expose the chair to high temperature, do not leave it near heating
devices or in the sun for a long time. If the chair malfunctions, do not
attempt to repair it yourself.
Every 6 months, check that the screw connections are secure. For regular
cleaning, use a soft cloth (dry or slightly dampened with water). Do not
use abrasive materials or harsh detergents. If the upholstery is heavily
soiled, use a detergent specifically designed for upholstery, according to
the instructions on its packaging.
If the scope of supply does not match the list on the diagram, contact the
point of purchase. If the chair starts squeaking, check that the screw
connections are secure. If you cannot adjust the backrest recline angle
and chair height, check that the lever is working correctly and that there
are no foreign objects in the mounting points. If the product is defective,
contact customer support (e-mail: support@lorgar.eu; online chat:
lorgar.com; feedback form: lorgar.com/for-users). For detailed
information on troubleshooting, see the complete User Manual, available
at lorgar.com/drivers-and-manuals.
The warranty period begins from the moment the product is sold
in a retail network to the end customer. To obtain warranty service, contact
the point of purchase and provide the product with the proof of payment.
The warranty period and service life are 2 years, unless otherwise
indicated by local law.
The manufacturer's warranty on Lorgar Chairs does not apply to:
Materials prone to wear and tear (upholstery, castors and armrests
coating, belts);
Defects resulting from natural wear and tear or natural ageing of the
product (scratches, dents, tears, cracks);
Damage caused by failure to comply with the recommendations in the
Quick Start Guide and full User Manual;
Damage caused by improper transportation or handling of the product
by the end customer.
ATTENTION!
Full
lorgar.com/warranty-terms.
The information provided herein is subject to change without notice to
users. Up-to-date information and detailed product description,
certificates, warranty terms are available in the complete User Manual at
lorgar.com/drivers-and-manuals. Manufacturer: ASBISc Enterprises
PLC, Iapetou, 1, Agios Athanasios, 4101, Limassol, Cyprus. Made in
China. Manufacture date is indicated on the package.
⑮ – Lumbar pillow
⑯ – Protective gloves (2 pcs.)
⑰ – Quick Start Guide
⑱ – Diagram
SAFE USE GUIDELINES
CARE AND MAINTENANCE
TROUBLESHOOTING
WARRANTY SERVICE
warranty
information
ADDITIONAL INFORMATION
ENG
is
available
at
3
Publicidad
