Publicidad
Prestazioni funzionali
LED segnalazione L1
Sul fronte è visibile una segnalazione ottica multicolore (rosso, verde, arancio), associata alla
funzionalità del dispositivo. Gli stati possibili sono qui di seguito riassunti:
ON
Acceso fisso
LAMP
500 ms ON, 1500 ms OFF
FAST
40 ms ON, 230 ms OFF
BLINK
40 ms ON, 1500 ms OFF
OFF
Spento
Il LED riassume una serie di segnalazioni, che sono visualizzate con un ordine di priorità come di seguito
descritto. Se sussistono contemporaneamente le condizioni per più di una segnalazione, viene visualizzata
quella a priorità maggiore e, al venir meno di quest'ultima, quella di priorità immediatamente inferiore.
ENG
53ABR1S – 16 A RELAY WITH POWER MEASUREMENT - AVEBUS – 1 DIN MODULE
The 53ABR1S device is an actuator with a 16 A relay output at 230 V with a built-in current sensor
and 1 input channel for current transformer, connection to AVEBus and connection for auxiliary power
supply. Installation on DIN rail, occupies 1 module.
Technical Specifications:
Mechanical elements (Figure 1)
Container:
1 DIN module (18.5 l x 89.7 h x 64.8 d) mm
Protection rating:
IP20 (IP40 when installed in DIN housing)
Terminals:
3 + 2 + 2 + 2-pole
Container colour:
grey RAL 7016
Fixing:
on rail DIN EN 50022
Weight:
72 g
Connections (Figure 2)
Mains V~ and load voltage measurement connections (M1)
Black removable polarised terminal board with bracket 3-pole 16 A 300 V~
Insulation stripping:
7 mm
Screw:
slotted screwdriver head 3.5 x 0.6 mm
Tightening torque:
0.5 Nm
Capacity:
flex wire 0.2 ÷ 2.5 mm2 (30 ÷ 12 AWG) rigid or flexible
Terminal L:
L Mains line V ~
Terminal N:
N Mains neutral V ~
Terminal 1:
Output (L interrupted)
Bus and Vaux connections (M2)
Bus terminal board
green removable with bracket 2-pole 10 A 250 V~
Terminal board for aux. power supp.: black removable with bracket 2-pole 10 A 250 V~
Insulation stripping:
5 mm
Screw:
Tightening torque:
0.5 Nm
Capacity:
0.05 ÷ 2.5 mm2 (23 ÷ 14 AWG) rigid or flexible
Opening:
2 mm x 2.5 mm
Terminal 1:
BUS positive
Terminal 2:
GND
Terminal 3:
auxiliary power supply positive
Terminal 4:
GND (auxiliary power supply negative)
Toroid external current measurement connection (M3)
Terminal boards:
spring type 2-pole 13 A 160 V~
Insulation stripping:
8 mm
Capacity:
0.2 ÷ 1.5 mm2 (24 ÷ 16 AWG) rigid or flexible
Terminal 1:
toroid
Terminals 2:
toroid
Mains voltage
Max. measurable voltage:
260 V ~
Mains frequency:
50 ÷60 Hz
@ VN = 230 V~
Set V > V
@ 265 V~
Reset V > V
MAX
Set V < V
@ 154 V~
Reset V < V
MIN
@ VN = 115 V~
Set V > V
@ 133 V~
Reset V > V
MAX
Set V < V
@ 77 V~
Reset V < V
MIN
Max. power dissipation
@ Vi = 230 V~ 50 Hz, load = 16 A: 4 W
@ Vi = 115 V~ 60 Hz, load = 16 A: 4 W
AveBus parameters
Absorption (C)
With device powered by aux. source
C = 0.3 (37 uA
With device powered by BUS
C = 66 (35.5 mA
DS capacity
DS = 1
300 pF (Device protection capacity)
Auxiliary power supply
Rated voltage:
12 Vac/dc
Permitted variation:
10.5 V: 14V
slotted screwdriver head 3 x 1 mm
@ 253 V~
MAX
@ 182 V~
MIN
@ 126 V~
MAX
@ 91 V~
MIN
)
MAX
; 32.5 mA
)
MAX
AVG
Allarmi (priorità alta)
FAST rosso
dispositivo in programmazione (o in aggiornamento) o in
individuazione in corso
ON rosso
carico interrotto o di potenza inferiore al minimo
LAMP rosso
protezione da sovraccarico intervenuta o tensione superiore alla
soglia max
Stato dell'uscita (priorità media)
ON arancio
carico ON
Alimentazione (priorità bassa)
ON verde
Bus assente o circuito non funzionante, alimentazione ausiliaria
presente.
LAMP verde
Bus presente, tensione misurata assente o al di sotto della soglia
minima
BLINK verde
Bus presente (normale funzionamento)
Absorption @ 12 Vdc:
34 mA
Weather Conditions
Reference Temperature and Relative Humidity: 25°C RH 65%
Operating temperature:
-5°C ÷ + 35°C
Maximum Relative Humidity:
90% at 35°C
Max altitude:
2000 m a.s.l.
Installation and Maintenance Rules
Installation and maintenance operations must be performed by qualified personnel in compliance with
the regulations governing the installation and maintenance of electrical equipment in force in the country
where the products are installed.
• Before using the device, make sure that the power supply has been disconnected by turning off
the main switch.
• The device must be protected with an easily accessible circuit breaker.
• This device complies with the reference standard, in terms of electrical safety, when installed in
the relative control unit.
• If this device is used for purposes not specified by the Manufacturer, the protection provided may
be impaired.
• Respect the maximum current and voltage values indicated for the device.
• The terminal boards for Bus and auxiliary voltage connection must be covered with the special
cover supplied.
• The receiver, with the load switched off, does not guarantee galvanic isolation separation (> 3
mm). The circuit on the load side must be considered always live.
• An appropriate assessment of the power dissipation from the complete panel must be carried
out, bearing in mind that each device dissipates the stated full-load power.
• The measuring toroid cables must not be longer than 45 cm.
• Current transformers with a transformation ratio of less than 1000 are not allowed: 1
Regulatory compliance
AVE SpA declares that the radio equipment complies with Directive 2014/53/EU. The full text of the EU
Declaration of Conformity can be found in the product data sheet at the following address: www.ave.it.
RoHS Directive 2011/65/EU
REACh Regulation (EC) No. 1907/2006
EN 60669-2-1
Non-automatic switchgear for household and similar fixed electrical installations -
Part 2-1: Special requirements - Electronic switches
EN 50428
Switches for household and similar fixed electrical installations - Collateral
Standard - Switches and related accessories for use in home and building
electronic systems (HBES).
WEEE - Information for users
The crossed-out bin symbol on the appliance or on its packaging indicates that, at the end of
its life, the product must be collected separately from other waste. The user must therefore deliver
the equipment to appropriate separate collection centres for electrotechnical and electronic waste.
Alternatively, the equipment can be handed over, free of charge, to the distributer when a new piece
of equivalent equipment is purchased. Distributors of electronic products with a sales area of at least
400 m2 can also deliver electronic products to be disposed of with a size of less than 25 cm free of
charge, with no obligation to purchase. An efficient separate waste collection leading to the subsequent
recycling of the disused appliance, or disposal compatible with the environment contributes to avoiding
negative effects on the environment and health and favours the re-use and/or recycling of the materials
which the components of the appliance are made of.
Loads controllable at the line voltage of 230 V ~ 50 Hz
Power
Load type
Min.
3
10
10
3
10
10
3
10
(73 mA
)
AVG
MAX
U.M.
Max
3680
1840
1150
1) max 6 transformers
1)
2) max 30 lamps
230
[W]
3) not corrected
2)
4) corrected parallel, max 130 uF
5) max 20 lamps
1150
3)
6) max 4 transformers
800
4)
450
5)
1150
[VA]
6)
Publicidad
