Publicidad
• Do not overload the stroller! Any load placed and / or attached to the handle, board, backrest, canopy and /
or sides of the stroller can affect its stability! The stroller and the seat are designed to carry only one child!
• Do not use spare parts and other components not supplied by the manufacturer! The manufacturer accepts
no liability for safety if used spare parts, different from the original ones or approved by the approved type.
• Do not make changes or modifications to the construction! If necessary, contact your supplier or an
authorized service centre for advice and repair.
• The car seat does not replace the baby seat or crib. When the baby does not need sleep, it should be placed
in a suitable baby stroller, seat or crib.
• Do not use the product if you find any missing or damaged parts!
• Do not allow children under 3 years of age to fully assemble the product to avoid access to small and
disassembled parts!
• Do not place additional cords or ties on the product to avoid the risk of suffocation!
• Do not use the stroller on escalator and be careful when getting down or up on the sidewalk.
• Keep the plastic packaging away from children to avoid the risk of suffocation!
• DO NOT store the product in humid places and in direct sunlight!
SEE FIGURE PD:
PD: 1.Handle; 2.Canopy; 3.Rear wheel; 4.Safety board; 5.Upholstery; 6.Front wheel orientation; 7.Adjustable
footrest.
1. UNFOLDING THE STROLLER – FIGURES 1-3: Pull the handle up until the frame reaches the end position. You
should hear a click when the frame locks.
2.INSTALLING AND REMOVING THE FRONT WHEELS – FIGURES 4-5: Insert the front wheel into the front
frame hole, as shown in Figure 4. Fix it until you hear a "click". To remove the front wheels, press the metal clip
and the wheels are removed easily by pulling out (Figure 5).
3.ORIENTATION OF THE FRONT WHEELS – FIGURE 6: Press the lever downwards to activate the straight
direction of front wheels. Pull the lever upwards to activate the swiveling of front wheels.
4.INSTALLING AND REMOVING THE REAR WHEELS – FIGURE 7: Insert the rear wheel into the hole of the rear
frame, as shown in Figure 7. Fix until you hear a click. To remove the rear wheels, push the button and the
wheels are released quickly by pulling out.
5.USING THE BRAKE ON THE REAR FRAME– FIGURE 8:
wheels, press down the pedal on the rear axle (Figure 8). To release the brake, pull up the pedal using your
foot.
6.ADJUSTING SEAT TILT - FIGURES 9: Press the strap system button on the back of the seat and move it up to
adjust the seat to the seated position. Press the strap system button and move it down to adjust the seat to
the horizontal position.
7.USING THE FOOTREST – FIGURE 10: To adjust the footrest, hold the button on both sides for its release.
8.ATTACH AND DETACH THE SAFETY BOARD – FIGURE 11: Insert both ends of the safety board into the two
side holes of the frame. Secure the guard until you hear a click. To remove the guard, press the release button
on both sides of the frame and pull at the same time. The safety bumper has a function of pivoting, it can be
opened just one side for easier taking care of baby or putting it in or taking it out.
9. FOLDING THE STROLLER – FIGURES 12-13: Before folding the stroller, activate the parking device and fold
the canopy. Simultaneously hold the unlock button and the fold button on the stroller frame (figure 12) and
push the handle forward until the stroller folds.
10.5-POINT SAFETY BELT – FIGURE 14 To attach the belt, insert the two tabs of the lap belt into the buckle on
both sides, should click when properly inserted. The shoulder straps are fitted as the metal tabs are assembled
and inserted into the buckle. The sliding adjusters are fitted and must be carefully adjusted on each side so
that the belt is fastened around your child without causing discomfort. To release the bely, press the buckle
button, and pull to open.
ASSEMBLY STEPS AND USE
CLEANING AND MAINTENANCE OF THE PRODUCT
PARTS
To activate the parking device and lock the two rear
17
Publicidad
