Descargar Imprimir esta página

Reelcraft RT Serie Instrucciones De Operación

Carretes accionados por resorte

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Operating Instructions
Spring Driven Reels - Condensed Version
Series RT
Series 4000 / 5000
Series 3000
Series 5005
Read these instructions carefully before attempting to install, operate, or
maintain your reel. Only qualified persons should install this product. Failure
to comply with instructions may result in personal injury and/or property
damage. Every attempt is made to ensure the accuracy and completion of
Safety
1. Only use designated fluid media as specified by manufacturer.
Contact manufacturer for information regarding other fluid media
uses.
2. Before connecting reel to supply line, ensure that pressure and
temperature does not exceed maximum rating of reel.
3. Remember, even low pressure is very dangerous and can cause
personal injury or death.
4. Do not exceed maximum installation height. The maximum
installation height is 16 feet unless expressly specified.
5. A high tension spring assembly is contained within the reel.
Exercise extreme caution. Do not open tamper-resistant
compartment on Series RT, 80000, SD, 9000, and HD70000 reels.
6. Remove all spring tension before beginning disassembly process.
7. Ensure that reel is properly installed before connecting input and
output hoses.
8. Bleed fluid/gas pressure from system before servicing
reel.
9. If a leak occurs in the hose or reel, remove system pressure
immediately.
10. Pull hose from reel by grasping the hose itself, not the hose end
attachment.
11. Operator should always walk hose back to reel during retraction.
12. If reel ceases to unwind or rewind properly, remove system
pressure immediately. Do not jerk excessively on the hose!
13. Treat and respect the hose reel as any other piece of machinery,
observing all common safety practices.
Installation
For Series 80000, SD, and 9000 reels: A flexible connection
must be used between the reel inlet swivel and the source
of supply. A rigid connection will damage the reel and void
all warranties. For all other series, Reelcraft recommends a flexible
connection between the reel input and the source of supply. Series
80000, SD, and 9000: the swivel union is packed separately in the
reel carton, use teflon tape or pipe sealant to assure a satisfactory seal
when installing swivel. Do not over tighten.
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com
Series 7000 / RS7000
Series DP
these instructions; however, Reelcraft is not responsible for ommissions.
To obtain the complete version of Reelcraft's service manuals, technical
bulletins, and other support, please visit www.reelcraft.com or call customer
service during business hours.
Mounting & Guide Arm Adjustment
The hose reel is equipped for universal mounting so that it can be
mounted on a structurally sound floor, wall, or ceiling; whichever
provides maximum performance. The hose guide arm must be rotated
to a position that allows the hose to feed through the roller brackets
with minimal bending. Replace the fasteners. When rotating guide
arm, the U-bolt must be placed in the proper location, otherwise the
reel might "latch or lock out" during use. Refer to complete version of
online manual for proper U-Bolt locations (not applicable for Series
RT, DP5000, DP7000, or SD).
Lubrication
Hose reel spring and bearings are factory-lubricated and require no
further lubrication.
Install/Replace the Hose
CAUTION: Exercise extreme caution when adding or removing
spring tension. Ensure reel base is fastened down prior to
adjusting tension. Do not move spool while tightening hose or
latch will disengage. Do not let go of the hose until latch mechanism
is engaged.
1. To achieve proper tension, wind spool flange required number of
turns (refer to online Tech Bulletin). Do not over-tighten.
2. Engage hose latching mechanism.
3. Insert hose through roller guide.
4. Connect hose fitting to female outlet. Install hose stop at desired
position.
Spring Tension Adjustments
To adjust spring tension, add or remove wraps of hose from the spool,
one wrap at a time, until desired tension is obtained (refer to safety
cautionary statements). Hose latching mechanism can be removed
for constant tension applications.
Repairs
To avoid damage and/or injury, extensive repairs should only be
performed by the manufacturer's service center. Noncompliance may
void warranty. CAUTION: Remove all spring tension and system
pressure before disassembly process.
Series HD70000
Series SD
Series 80000
Series 9000
Form #1212-1108 Rev: 6/2023

Publicidad

loading

Resumen de contenidos para Reelcraft RT Serie

  • Página 1 CAUTION: Remove all spring tension and system pressure before disassembly process. Form #1212-1108 Rev: 6/2023 Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605 Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com...
  • Página 2 No apriete en exceso. Form #1212-1108 Rev: 6/2023 Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605 Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com...
  • Página 3 à l’installation du raccord. Ne le serrez pas avec excès. Form #1212-1108 Rev: 6/2023 Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605 Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com...
  • Página 4 Para obtener mayor información acerca de la garantía, visite www.reelcraft.com. Form #1212-1108 Rev: 6/2023 Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605 Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com...

Este manual también es adecuado para:

3000 serie4000 serie5000 serie5005 serie7000 serieRs7000 serie ... Mostrar todo