DeWalt DXSTFH030KD Manual De Instrucciones

JS PRODUCTS | 6445 MONTESSOURI STREET, LAS VEGAS, NV 89113
(JUL18) Part No. 41608
Copyright © 2018 D
D WALT and the D WALT Logo are trademarks of the D
®
E E
and are used under license. The yellow/black color scheme is a trademark for D
Definitions: Safety Guidelines and Words
This instruction manuals use the following safety alert symbols and words to alert you
to hazardous situations and your risk of personal injuery or property damage.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury which, if not avoided,
may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D
CALL US TOLL FREE AT: 1-844-377-8451
WARNING! Read and understand all instructions.
important safety and operating instructions.
before assembling this storage rack and save it for reference.
SAVE THESE INSTRUCTIONS
READ ALL INSTRUCTIONS
BEFORE YOU BEGIN:
• Read all instructions thoroughly.
• Remove all components from the box, and lay them on the floor in an orderly fashion.
• Wear eye protection.
• Be cautious of sharp edges.
• Do not stand on product. You may fall which may cause personal injury.
• 300 lb weight limit.
• Keep this information for further reference.
Parts List
No. Description
1 Upright A
2 Upright B
3 Crossbeam
4 Wire Decking
5 Swivel Bracket
6 Cushion Seat
7 Top Securing Bracket
8 Bottom Securing Bracket
DXSTFH030KD Copyright © 2018, D WALT
E
WALT.
E
WALT Industrial Tool Co., or an affiliate thereof
E
WALT power tools
E
& accessories.
WALT TOOL,
E
This manual contains
Please read this manual carefully
Qty. No. Description
1 9 D WALT Carriage Bolt
E
2 10 Washer
4 11 Nut
1 12 Clip Spacer A
1 13 Clip Spacer B
1 14 Machine Screw
4 15 Screw
4
1
2
3
Stool Body Instructions (Fig. 1-3)
1. Position the uprights of the stool so they may be bolted together (Fig. 1). Using the machine screws, bolt
together the uprights using the 4mm hex key.
2. Next, slide a crossbeam onto the stool uprights tab slots. It is recommended to install the crossbeam two slots
above the feet. Make sure the crossbeam is level then install a second and third crossbeam.
3. Install the wire deck. The wire deck will need to be turned sideways and positioned to rest on the ledges of the
crossbeams (Fig. 2). Install the remaining crossbeam. (Fig. 3)
4. Make sure that all the tabs on the crossbeams are inserted properly and then tap the crossbeams down with a
rubber mallet to seat them fully.
5. Secure the crossbeams to the uprights using the D
FIG. 1
UPRIGHT B
UPRIGHT A
UPRIGHT B
Wire Deck Securing Bracket Instructions (Fig. 4-5)
1. The wire decking will have the clip spacers already installed. Check to make sure the clip spacers have been
installed with the open-end facing upwards on each rod of the wire decking. There are two clip spacers per
side of the wire decking. See Fig. 4 for correct placement.
2. From the underside of the decking, use the dowels of the bottom securing bracket to position it into the
correct orientation in the corner of the crossbeams. The crossbeams will have a locating hole for dowels.
Qty.
3. Place the top securing bracket on top of the wire decking to snap into the bottom securing bracket.
8 4. Fasten the top and bottom securing brackets together using (3) of the supplied screws.
5. Repeat this process for the remaining three corners.
8
8
FIG. 4
4
CLIP
CLIP
SPACER A
4
SPACER B
12
12
CLIP
CLIP
SPACER B
SPACER A
4
5
6
7
8
WALT badged carriage bolt, washer, and nut.
E
FIG. 2 FIG. 3
WIRE
DECKING
FIG. 5
SCREW
TOP BOTTOM
SECURING SECURING
BRACKET BRACKET
9
10
11
12
13
14
15
CARRIAGE
BOLT
CROSSBEAM