Publicidad
Idiomas disponibles
Idiomas disponibles
RC-30
1. Description.
RC-30 is a wireless, easy to use remote control intended for wireless control of the CPX300W alarm system, with which it cooperates.
With the use of the buttons, the user will be able to arm/disarm the system or call suitable help. Each button can be programmed individually to the
needs of the person to whom it will be assigned (several functions are available).
2. Features.
Two-way radio communication,
5 programmable buttons (4 on the front and 1 on the back),
Multicolour LED signalling the status of the alarm system,
Low battery level control.
3. LED signalling.
Disarming – 2-time quick flash of green diode,
Full arming – 2-time quick flash of red diode,
Daytime arming - 2-time quick flash of yellow diode,
Night-time arming - 2-time quick flash of blue diode,
Panic – a sequence of flashes of diodes: yellow, pink, blue, red (without interruptions),
Required confirmation of arming if the system is not ready – 1 flash of arming diode, followed by pink diode,
Command rejection (e.g. when the user has no authorization) - 3-time quick flash of pink diode,
No communication with CPX300W – pink diode turns on for a longer period,
Low battery level– white diode turns on after each of the above signals.
If the remote control has not been paired with any control panel, each press the button will light the blue LED once.
4. Battery installation.
battery and the device is in sleep mode. When the battery is
worn out it needs to be replaced. In order to do it, a straight
slot screwdriver should be applied to the place indicated in
figure 2 and turn it slightly along its axis. Repeat the action in
several points of the opening line until the case is fully
separated. Then, remove the PCB taking care not to damage
the buttons, remove the spent battery in the direction
indicated in figure 3, insert the new battery (with + up), place
the plate on the rear part and assemble the case.
NOTE: Do not press the buttons without the cover!
5. Specifications.
Frequency bands*
Range in an open space
Maximum power consumption
Average power consumption
Batteries
Operating time on batteries
Operating temperature
Maximum humidity
Dimensions
Total weight
Environmental class according to
EN50130-5
* National regulations may apply
7. Unpairing.
Remote control RC-30 can be unpair by:
Pressing DEL- button on the control panel's mainboard. The unpairing process will be signalled by lighting up the yellow LED above the button.
Pressing any button on the remote control will cause its unpair with the control panel, which will be signalled by single flash the blue LED in the
remote control. After unpaired, the control panel automatically returns to normal operation mode.
Pressing buttons on the remote control. To unpair the remote control, following steps have to be performed: press and hold the disarming button
-> after approx. 10 seconds the red LED will flash three times -> then (while still holding the disarming button) press the stay mode arming
button
twice. After the first press, the yellow LED will flash once, after the second press the remote control will unpaired, which will be
confirmed by a long flash of the blue LED. NOTE: Please remember that after unpairing the device, it should also be removed from the control
panel!
EBS Sp. z o. o.
ul. Bronisława Czecha 59, 04-555 Warsaw, POLAND
Technical assistance: tel. +48 22 51 88 477, e-mail: support@ebssmart.com
www.ebssmart.com
AVA PRO Remote control
RC-30 has pre-installed
868 MHz (ITU Region 1)
915 / 921 MHz (ITU
Regions 2 and 3)
to 800 m
37 mA
2.2 µA
1x lithium 3V CR2032
approx. 6 years
from -10 to +55°C
93±3%
35 x 73 x 8 mm
16 g
II
.
Fig. 1. Description of default button functions.
Fig. 2. Opening the case.
6. Pairing.
By default, in factory remote control the battery is inserted into the
socket and the device is in sleep mode. Pressing any button on an unpaired remote
control will cause "wake up" and the blue LED to light up once. It can be added to
the system using radio communication via:
Pressing ADD+ button on the control panel's mainboard. After pressing, the
control panel will enter the pairing mode, which will be signalled by lighting
up the yellow LED above the button. Then press any button on the remote
control – the LED blue light up once. When the control panel detects the
device, the green RFMON LED and the blue MODE LED will flash three times in
sequence
and the pairing will be confirmed by blinking the blue LED
in the remote control twice. NOTE: To exit the pairing mode, press the EXIT
button.
Use the "Detect Device" function in EBS Config 2.0 (see instructions for
EBS Config 2.0, Devices tab).
The remote control can also be added by entering the serial number in the EBS
Config 2.0 desktop application or by reading the QR code in the mobile application
of the same name. NOTE: Please note that adding devices in this way requires
sending the configuration to the control panel!
Fig. 3. Battery replacement.
RC-30_manual_PL_EN_ES_PT_v1.5
V: 1.1.0
Publicidad
