Publicidad
Idiomas disponibles
Idiomas disponibles
4. If the bag was used for dry pick up, simply grasp the plastic handle and remove from the
tank.
5. If the bag was used for wet pick up, grasp the plastic handle and slowly lift up on the bag.
Allow the liquid to drain from the bag into the tank. If the bag is not full, hang it up and allow
it to dry completely. Once dry, check the bag for tears or holes. If none are found the bag
can be reinstalled.
NOTE: Additional collection bags are available at your local dealer or the Shop-Vac ®
website.
WARNING FOR FINE DUST & POWDERS
When vacuuming fine dust, or powders of any kind (ex. plaster, drywall dust, cold ashes,
concrete dust, etc.), a high efficiency drywall filter bag must be used. When vacuuming
normal household dust and debris, standard household disposable filter bags may be used.
These "large bag" filters connect to the air inlet fitting on the inside of the vacuum tank.
FILTER SELECTION GUIDE
Fine dust
Standard
SIZE
Drywall
Household
5-8 U.S. Gal (18.9-30.3L)
90671/
H
10-14 U.S. Gal (37.8-53L)
90672/
I
15-22 U.S. Gal (56.8-83.2L)
90673/
J
5-10 U.S. Gal. (18,9-37,8L)
12-20 U.S. Gal. (18,9-37,8L)
WET PICK UP OPERATION
Remove ALL dirt and debris found in the tank. The vacuum requires only a minimum of
conversion when going from dry to wet pick up. Remove all dry use filters from the vacuum.
A clean cartridge filter may be used for vacuuming small amounts of liquids. For proper
installation of the cartridge filter refer to Installing the Cartridge Filter. For best results when
vacuuming large quantities of liquid, remove the cartridge filter. When vacuuming liquids
containing debris, it is recommended purchasing a foam sleeve and install over filter cage;
otherwise a foam sleeve is not required for wet pick up. Foam sleeve and additional filters
may be purchased by visiting our website at www.shopvac.com, contacting our customer
service department, or purchasing at your local Shop-Vac
Misting in exhaust air may occur if the filter becomes saturated during wet pick up. If misting
occurs, remove filter and allow to dry or, replace with another dry filter to eliminate the
misting and possible dripping of liquid around the lid. Turn the unit off immediately upon
completing a wet pick up job or when tank is full and ready to be emptied. Raise the hose to
drain any excess liquid into the tank. The interior of the tank should be periodically cleaned.
The foam sleeve should be cleaned periodically as described in the following steps:
1. Always disconnect the plug from the wall receptacle before removing the tank cover. Place
tank cover in an upside down position. Remove foam sleeve by sliding it up and off the lid
cage.
2. Shake excess dust off foam sleeve with a rapid up and down movement.
3. Hold foam sleeve under running water for a minute or two, rinsing from the inside. A water
wash is not always required, depending on the condition of the foam sleeve.
4. Gently wring out excess water, blot foam sleeve with a clean towel, and allow to dry. The
foam sleeve is now ready to be reinstalled on the lid cage.
NOTE: WET PICK UP ACCESSORIES SHOULD BE WASHED PERIODICALLY, ESPECIALLY AFTER
PICKING UP WET, STICKY KITCHEN ACCIDENTS. THIS CAN BE ACCOMPLISHED WITH A WARM
SOLUTION OF SOAP AND WATER.
INSTALLING BRUSH OR SQUEEGEE SHOE
ONTO 14" (35.56 CM) NOZZLE
(Not standard with all models)
1. Place shoe on flat surface with four tabs facing up and closest to you (Figure 75).
2. Position nozzle over shoe with large opening facing down and side with four slots is closest
to you (Figure 76).
3. Place edge of nozzle under two clips on shoe, located on side farthest away from you
(Figure 77).
4. Push down on the nozzle to attach shoe to nozzle.
5. Starting under left tab, push upward on bottom edge of shoe until tab snaps into place
(Figure 78). Repeat with remaining tabs. Make sure four tabs are locked into place.
6. Your nozzle with shoe is now ready for use.
7. If you ever need to remove shoe, simply unsnap four tabs and carefully pull shoe away from
nozzle starting on side with tabs.
75
90107/
REUSABLE DRY FILTER AND MOUNTING RING
S
fits most Shop-Vac
®
Wet/Dry Vacuums.
90661/
E
90585/
R
FOAM FILTER SLEEVE fits most Shop-Vac
90662/
F
Wet/Dry Vacuum
90663/
G
90215/
RR
90216/
SS
®
distributor.
76
77
Your vacuum can be used as a powerful blower. To use your unit as a blower, clear hose of any
obstruction. Insert machine hose end into blower port on rear of unit (Figure 79). Twist slightly
to tighten the connection. Caution should be used when using as a blower due to the powerful
force of air when using certain attachments.
WARNING
®
PREVENT ROCKS OR DEBRIS FROM BEING BLOWN OR RICOCHETING
INTO THE EYES OR FACE, WHICH CAN RESULT IN SERIOUS INJURY.
EMPTYING LIQUID WASTES FROM THE TANK
Not all units are equipped with tank drains. Follow the instructions,
which apply to your specific unit.
Without Tank Drain
Liquid waste may be emptied by removing the tank cover. To empty, stop the motor and
remove the plug from the wall receptacle. Remove the tank cover and deposit the liquid
waste contents in a suitable drain. After tank is empty, return the cover to its original position.
To continue use, plug the cord into the wall receptacle and turn the unit on.
With Tank Drain
Liquid waste may be emptied by removing the tank drain cap. To empty, turn unit off and
remove plug from wall receptacle. Remove the drain cap and deposit the liquid waste
contents in a suitable drain. After the tank is empty, return the drain cap to its original
position. To continue use, plug the cord into the wall receptacle and turn the unit on.
AUTOMATIC SUCTION SHUT-OFF
The vacuum is equipped with an automatic suction shut-off that operates when picking up
liquids. As the level of the liquid rises in the tank, an internal float rises until it seats itself
against a seal at the intake of the motor, shutting off suction. When this happens, the motor will
develop a higher than normal pitch noise and the suction is drastically reduced. If this occurs,
turn unit off immediately. Failure to turn unit off after float rises and shuts off suction will result
in extensive damage to the motor. To continue use, empty the liquid waste from the tank as
outlined in the previous paragraph.
NOTE: IF ACCIDENTALLY TIPPED OVER, THE VACUUM COULD LOSE SUCTION. IF THIS
OCCURS, PLACE VAC IN UPRIGHT POSITION AND TURN SWITCH OFF. THIS WILL ALLOW
THE FLOAT TO RETURN TO ITS NORMAL POSITION, AND YOU WILL BE ABLE TO CONTINUE
OPERATION.
No lubrication is necessary as the motor is equipped with lifetime lubricated bearings.
Before storing your vacuum cleaner the tank should be emptied and cleaned. The power cord
can be wrapped around the cord wraps provided on the tank cover on rear of unit (Figure 80).
Accessories may be stored in the tool holder (not standard on all models) so they can be
readily available. The vacuum should be stored indoors.
78
BLOWER FEATURE
– ALWAYS WEAR EYE PROTECTION TO
79
LUBRICATION
STORAGE
80
Publicidad
