Approx APPPCI1000 Guía De Usuario

FCC STATEMENT
The adapter has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
e Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
CHAPTER 1 INTRODUCTION
HARDWARE OVERVIEW
APPPCI1000 is a highly integrated and cost-effective single-chip Gigabit Ethernet
Adapter that provides 32-bit performance, PCI bus master capability, and full compliance
with IEEE 802.3 10Base-T, IEEE802.3u 100Base-TX and IEEE 802.3ab 1000Base-T
specifications. It also supports ACPI, PCI power management for modern operating
systems that are capable of Operating System Directed Power Management (OSPM) to
achieve the most efficient power management.
Through the aid of a VLAN membership, APPPCI1000 adheres to the 802.1Q for multiple
VLAN support, and 802.1P for packet prioritization. With 802.1Q support, server
resources can be shared with multiple VLANs when used in conjunction with any
802.1Qenabled Switch. With the 802.1p support, APPPCI1000 allows a range of
Ethernet packets to be prioritized from a critical to a non-critical designation through a
priority tag.
APPPCI1000 supports Full Duplex operations at 20/200/2000 Mbps data speeds used in
conjunction with 802.3x flow control support. With 802.3x flow control APPPCI1000 uses
both asymmetric and symmetric functions via the MAC control pause function. Any
4
participating 802.3x flow control node can be controlled by initiating a pause control to
stop incoming network traffic, to further reduce network congestion.
By default APPPCI1000 supports the standard 1518Byte frame size. In addition,
APPPCI1000 can also be configured to use a maximum Jumbo Frame size of up to 7680
Bytes.
lt includes an interface for a boot ROM and can be used in diskless workstations,
providing maximum network security and ease of management.
Also, being PCI 2.2 compliant, APPPCI1000 works with 32-bit 33Mhz PCI busses. This
compatibility provides users with an easy migration path to increase performance
between servers and workstations for large file transfer, video editing and server
clustering for data intensive applications.
FEATURES 8. ADVANTAGES
+» Integrated Ethernet MAC, Physical chip and transceiver in one chip
e Complies with the IEEE802.1P, IEEE802.1Q, IEEE802.3 10Base-T, IEEE802.3u
100Base-TX and IEEE802.3ab 1000Base-T standard
* Compliant to PCI Revision 2.1/2.2
* Supports Full Duplex Flow Control (IEEE 802.3x)
+ PCI local bus single-chip Ethernet controller
+ Supports ACPI, PCI power management
* Supports Auto-Negotiation function, Auto-detects network speed
* Contains two large independent receive and transmit FIFOs
+ One STP/UTP connector
e Provides LEDs to indicate network Link/Activity/Speed/ Duplex
e Supports smart remote boot ROM
e Supports Drivers for NetWare 4.x,5.x,6.x,Windows 98, Windows ME, Windows NT,
Windows 2000, Windows XP, Linux
CHAPTER 2 INSTALLATION
CARD INSTALLATION
To insert The Product into your computer, follow the steps list below.
1 Turn off the computer and remove its cover.
2 Insert APPPCI1000 into a PCI slot.
3 Fix the Product to the rear of the computer chassis and put the computer cover in order.
4 Connect the adapter to the network with twisted-pair cables.
DRIVER INSTALLATION
The required software is in the diskette.
English
APPENDIX A: TROUBLESHOOTING
If you experience any problems with the adapter, first please confirm that the appropria-
te driver is loaded properly,and that the cable is connected to the adapter port soundly.
Then check the LED. The Product provides LEDs to indicate network status.
10 LED, 100 LED, 1000 LED
They all indicate Link/Active/Speed status.
When the 1000 LED is lit, it indicates adapter has been linked to network with the right
speed of 1000Mbps. The flash 1000 LED indicates data transmission at the responding
port.The 10 LED and 100 LED are similar to the 1000 LED.
FDX LED
It indicates the status that whether or not the adapter works at full duplex mode. When
the LED is lit the adapter works at full duplex mode. Otherwise the adapter works at half
duplex mode.
If you have other questions, please contact our local FAE.
APPENDIX B: TECHNICAL SPECIFICATION
* Topology: Star
e Connector Supported: Rj45
e Standard: IEEE802.1P, IEEE802.1Q , IEEE802.3 10Base-T,
IEEE802.3u 100Base-TX, IEEE 802.3ab 1000Base-T
e Transmission Rate: 10/20Mbps , 100/200Mbps, 2000Mbps
» Hardware: IBM PC compatibles(It must have PCI slot)
+» IRQ Line: Assigned by system
+ I/O Address: Assigned by system
* Software: Supports Drivers for NetWare 4.x,5.x,6.x, Windows 98, Windows ME,
Windows NT, Windows 2000, Windows XP, Linux
* Temperature: 0 to 40 (Operating)
e Humidity: 10% to 90% (Non-condensing)
+ Power consumption: 4W(Max)
aqprox /
ui
PCTIOOO | con
GUIA DE USUARIO
USER GUIDE
32bit Gigabit PCI Network Interface Card
APPPCIIO00
www.printyourideas.com