Landxcape LX835i Manual Del Propietário página 21

Symptom
The LED light on the charging station
does not turn on.
Red light turns on the charging station.
TM
Landxcape turns on, but the blade
disc does not move.
TM
Landxcape vibrates.
Grass is being cut unevenly.
TM
Your Landxcape is inside its territory
and the boundary wire is connected.
And " " is displayed.
The charging time is far more than the
rated charging time.
The mower does not charge.
TM
Landxcape is starting to have shorter
run-times between charges.
TM
Landxcape is not operating at the
correct time.
TM
Landxcape cannot correctly dock
with the charging station.
EN
Cause
There is no power.
The boundary wire isn't connected.
TM
Landxcape is searching for the charging
station (unless you press then
to make it go to the charging base)
Blades may be damaged. Check condition of
the blade disc.
TM
Landxcape does not work enough hours per
day.
Mowing area is too big.
Blades are dull.
The cutting height is too low for the length of
the grass.
Grass or other object has wrapped around the
blade disc.
There is a build-up of grass in the blade disc or
motor frame box.
The boundary wire ends are clamped
incorrectly.
The boundary wire is broken.
Poor connection caused by debris on the
charging strip.
The charging protection program has activated
due to high temperature.
There is no power.
TM
Landxcape does not operate correctly while
manually charging.
Something is clogging in the blade disc.
TM
Landxcape is shaking heavily.
The battery may be exhausted or old.
The clock is not set to the correct time.
Programmed cutting times for Landxcape
are not correct.
TM
Landxcape is manually docked in the
charging station.
The battery does not charge as its temperature
O
rises above 55 C in hot weather.
Environmental influences.
Poor connection caused by debris on the
charging strip.
Check the charging station is connected properly to
the charger and the charger is connected to a suitable
power supply.
Check that the boundary wire has been connected
correctly to the charging station.
Check there are no breaks in the boundary wire, especially
in the wire ends.
This is normal. Landxcape
button blade disc does not rotate while it is searching for the
charging station automatically.
Check the blades, and replace them if damaged.
Remove debris and foreign objects from the blades
and blade disc.
Add more hours to the scheduled mowing time.
Try decreasing the size of the mowing area or adding
more hours to the mowing time.
Change all the blades and screws in order to balance
the blade disc.
Raise the cutting height and then gradually lower.
Check the blade disc and remove the grass or other
object.
Make sure the blade disc rotates easily. If need be, you
may take off the blade disc and remove the debris.
Reverse the boundary wire ends.
Repair damaged boundary wire with connectors.
Clean the contact pins located on the charging station
and the charging strip on Landxcape
Place the charging station in a shady area or wait
until the temperature has cooled down.
Check the power cord is connected properly to the
charger and the charger is connected to a suitable
power supply.
Refer to manual charging in Section 7.3.
Take off the blade disc and clean it.
Check the blade disc and blades, remove debris and
foreign objects from the blades and blade disc.
Replace battery.
Set the clock to the correct time, refer to Section 4.3.
TM
Change the time settings for the mower to start and
stop.
Press then .
Wait until the battery has cooled down.
TM
Restart Landxcape .
Clean the contact pins located on the charging station
and the charging strip on Landxcape
Action
TM
needs to recharge, the
TM
using a cloth.
TM
using a cloth.
21