Makita WST01 Manual De Instrucciones página 3

Ocultar thumbs Ver también para WST01:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

ENGLISH
Models:
LS1013, LS1016, LS1017, LS1018, LS1214, LS1212, LS1216, LS1030N, LS1040, LH1040, LS1220, LS1221, LS0714,
MT230, M243, MLS100, BLS713
Inclusive of models followed by F, L and FL, if any.
Preparation
Note: Check contents of package for the following components. Please inform Makita service center of any part missing in
the package immediately.
• Miter saw stand assembly (1 unit)
• Hex wrench 6 (1 pc.)
• Wrench 13 (1pc.)
• Hex socket bolt M8 x 16 (4 pcs.)
• Hex socket bolt M8 x 30 (4 pcs.)
• Hex bolt M8 x 50 (4 pcs.)
• Washer 8 (4 pcs.)
1.
Wheel 300
2.
Foot arm
3.
Handle
4.
Adjusting bolt
5.
Hex socket bolt M8 x 16
6.
Flat washer 8
7.
Leg B
Symbols
............. Read instruction manual.
............. Maximum allowable loading
MAX.
100Kg
(220 lbs.)
CAUTION:
• Read and thoroughly understand this manual and the
instruction manual of the tool you use before
performing the following.
• Before installing a tool on this stand, always switch off
and unplug the tool.
• The stand should be bolted in a stable and level
surface using the bolts provided on two of four feet.
• Use only with Makita model indicated in the instruction
manual.
• Use only the handle to avoid pinched fingers when
raising or folding the stand.
• Before operating the tool, secure it to stand using bolts.
• Do not use the stand on uneven or unstable surface.
• Do not climb, sit or stand on the stand.
• When setting up the miter saw stand in the upright
position or folding it, be sure to securely keep pressing
the pipe of miter saw stand with your foot until it locks.
• When storing miter saw stand, never lean it against the
wall or the like lengthwise or sideways.
• Never pull the locking lever without holding the handle.
Assembling miter saw stand (Fig. 1)
Assemble parts for miter saw stand as disassembled parts
are packed in the carton box.
(1) Adjusting bolt
• Wheel 300 (2 pcs.)
• Washer 8 (2 pcs.)
• Foot arm (1 pc.)
• Handle (1 pc.)
• Adjusting bolt (2 pcs.)
• Clamping nut M12 (2 pcs.)
Explanation of general view
8.
Leg A
9.
Hex socket bolt M8 x 30
10. Hex bolt M8 x 50
11. Hex nut M8
12. Hole
13. Wood Plate
14. Locking lever
(2) Wheel 300 (2 pcs.)
(3) Foot arm
(4) Handle
Installing a miter saw models specified
below on the miter saw stand: (Fig. 2)
Place a miter saw so that the hole in the miter saw base
overlaps a hole in the label on the miter saw stand table
according to applicable models. These holes come with
nut M8 (4 pcs). Secure the miter saw stand with Hex bolt
M8 x 50 (4 pcs.)
LS1013, LS1016, LS1017, LS1018, LS1214, LS1212,
LS1216, LS1030N, LS1040, LH1040, LS1220, LS1221,
LS0714, MT230, M243, MLS100
Installing a miter saw models other than
above models on the miter saw stand with
pitches between the holes in miter saw
15. Shift lever
16. Pin 10-60
17. Stopper
18. Extension arm
19. Lever 40
20. Clamping screw M8 x 20
21. Leg pipe 28
Place the stand assembly upright and insert adjusting
bolts (2 pcs.) from the below and secure these bolts by
tightening nuts.
To adjust, turn the adjusting bolts until it reaches floor
so that the miter saw stand can be kept stable.
Insert the wheels onto the leg B of miter saw stand on
both sides and secure the wheels by tightening hex
socket bolt M8 x 16 (2 pcs.) with washer 8 (2 pcs.)
from upper side.
Insert the foot arm onto the port of the leg B from
upper side and secure it by tightening hex socket bolt
M8 x 16 (2 pcs.) from backside.
Insert the handle onto the miter saw stand from the
cover side and secure it by tightening hex socket bolt
M8 x 30 (4 pcs.) from the ratchet cover side.
3

Publicidad

Tabla de contenido
loading

Tabla de contenido