Safety Instructions; Technical Data; Proper Use; Before Starting The Equipment - EINHELL BT-TJ Manual De Instrucciones

Gato hidráulico para coches sobre rodillos
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Anleitung_BT_TJ_2020_SPK7:_
Important!
When using the equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating instructions and
safety regulations with due care. Keep this manual in
a safe place, so that the information is available at all
times. If you give the equipment to any other person,
hand over these operating instructions and safety
regulations as well. We cannot accept any liability for
damage or accidents which arise due to a failure to
follow these instructions and the safety instructions.

1. Safety instructions

Before you raise the load, check that the
lowering screw is tightly shut.
Always place the hydraulic trolley jack on firm
and level ground when using it to raise a load.
Never work underneath a raised load which is
supported only by the hydraulic trolley jack.
Working on and under raised vehicles is only
permitted when the vehicle in question is
secured and supported against tipping and
slipping.
The trolley jack is designed only for raising loads.
After a load is raised it must be supported
immediately by at least one jack stand. Vehicles
must be sufficiently secured against rolling
before they are raised with the trolley jack. Never
use the trolley jack at an angle.
Position the trolley jack only where specified by
the vehicle manufacturer.
Make sure that no one leans against a raised
vehicle or load.
2. Layout (Fig. 1)
1. Drain screw
2. Piston rod mount
3. Carry-handle
4. Lifting arm
5. Support plate
6. Roller
7. Guide roller
8. Piston rod

3. Proper use

The hydraulic car jacks comply with EN1494: 2000.
They are designed for lifting loads, preferably cars, at
an ambient temperature of over 0°C.
24.06.2009
7:59 Uhr
Seite 3
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Lifting (load) capacity (kg):
Min. lifting height (mm):
Max. lifting height (mm):

5. Before starting the equipment

Air pockets may form in the hydraulic fluid passages
if the jack is not used for a long time or if there is too
little fluid in the hydraulic system from the outset.
In both cases, proceed as follows:
a) Topping up with oil (Fig. 2)
Remove the cover plate. On the hydraulic cylinder
you will see a rubber plug in the fluid filler hole. With
the trolley jack in horizontal position on the floor,
remove the rubber plug by pressing it in on the side
with a screwdriver. Fill in hydraulic fluid (type: HLP
32 Iso or equivalent) through the fluid filler hole.
You must fill in enough fluid to cover the cylinder
visible inside. Re-insert the rubber plug in the filler
hole.
b) Venting (Fig. 2)
The hydraulic system has to be vented at least after
each time you add hydraulic fluid. Air pockets may
also form in the hydraulic fluid passages if the jack is
not used for a long time. This is the case if the load
sinks again abruptly after being raised half or only
part of the way.
To vent the hydraulic system, pump up the unloaded
jacking arm approximately half way. Now press your
foot against the jacking arm to exert a little pressure
on the hydraulic system. The lowering screw must of
course be closed when you do this.
Use a screwdriver to press the rubber plug slightly
sideways until the air escapes. Now lower the trolley
jack by opening the lowering screw and repeat the
procedure 2 or 3 times. Air is also vented from the
GB
2000
135
330
3

Publicidad

Tabla de contenido
loading

Tabla de contenido