Cleaning, Maintenance And Ordering Of Spare Parts; Ordering Replacement Parts; Disposal And Recycling - EINHELL BT-TJ Manual De Instrucciones

Gato hidráulico para coches sobre rodillos
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Anleitung_BT_TJ_2020_SPK7:_
GB
system via the lowering screw. Any drops of fluid
which may then escape are irrelevant for the jackʼs
further use. You can now rest assured that there are
no longer any air pockets in the fluid passages and
that the jack will work correctly.
Catch old and escaping fluid in a special
container and deliver to your old oil disposal
center!
6. Raising vehicles (Fig. 1)
Before you raise a vehicle, make sure it is standing
on a firm surface so that the trolley jack does not sink
into the ground under the raised load. In hot summer
conditions the trolley jack may easily sink into tarmac
surfaces and slip sideways.
Pull the hand brake and also secure the vehicle with
chocks if available. Now place the trolley jack under
the vehicle so that the support disk can rest against a
strong part of the floor. On old vehicles with rusted
floor elements there is the risk of the support disk
breaking through the floor.
Make sure that the lowering screw is closed. Use the
jacking bar to pump up the jacking arm to a point
where it is not quite touching the vehicle. You can
now make final adjustments of position to ensure that
the vehicle is raised correctly and safely.
For your own safety, always use at least one jack
stand to provide additional support for a raised
vehicle with only one wheel off the ground.
When you have completed your work, first remove
the jack stand and then lower the jacking arm of the
trolley jack by slightly unscrewing the lowering screw
with the jacking bar. You can control the lowering
speed yourself by opening the lowering screw to a
greater or lesser degree. The trolley jack is equipped
with an overload valve on the side of the hydraulic
pump. This valve is set at the factory so that the
maximum load cannot be exceeded.
Do not adjust this valve or you will forfeit your rights
under the warranty if the jack suffers any damage.
Once the jacking arm reaches its highest position,
the safety valve and an overflow device will prevent
additional pressure being exerted on the hydraulic
system even if you continue to pump with the jacking
bar.
4
24.06.2009
7:59 Uhr
Seite 4
7. Cleaning, maintenance and ordering
of spare parts
7.1 Maintance
All moving joints should be oiled and the roller
bearings of the steering wheels greased every three
to six months, depending on how often the trolley
jack is used. Every hydraulic system is sealed with
O-rings or cup packings which result in wear
depending on how often the trolley jack is used.
Repair sets are available from Customer Service on
request. To prevent damage to the seals, use only
acid-free hydraulic fluid to top up the system.
Catch old and escaping fluid in a special
container and deliver to your old oil disposal
center!
You should always move the hydraulic system
(piston) to idle position (piston inserted) once the
trolley jack is no longer needed. This will protect the
precision-machined surfaces of the piston and the
piston rod from corrosion.
Your trolley jack will give you good service if you use
only high-grade hydraulic fluid. Never mix different
types of fluid! Never use brake fluid, alcohol,
glycerin, dirty fluid, etc.

7.2 Ordering replacement parts:

Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info

8. Disposal and recycling

The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.

Publicidad

Tabla de contenido
loading

Tabla de contenido