Disinfection Of Feeding Bottles, Teats And Accessories; General Information On Disinfecting; Disinfection; Please Observe The Following - NUK VAPO RAPID Manual De Instrucciones

Ocultar thumbs Ver también para VAPO RAPID:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 34
Vaporisator 09/08 Seite 17 Dienstag, 7. Oktober 2008 8:17 08

5. Disinfection of feeding bottles, teats and accessories

5.1 General information on
disinfecting
Newborn babies do not initially have sufficient
antibodies to be able to protect themselves
from pathogenic germs. For this reason it is vital
that disinfected teats and bottles are used when
preparing infant feeds. Even the most minute
food particles left on teats and feeding bottles
can easily lead to a build-up of bacteria, which is
a health hazard to infants. Components should
therefore also be cleaned each time before dis-
infecting. The steam steriliser uses heat to disin-
fect the components. Water is heated to above
90 °C and is converted into steam. The heat
generated therefore disinfects the components
inside the steriliser swiftly and reliably. This way
the teats and feeding bottles only come into
contact with heat and steam. As the steam ster-
iliser uses very little water, only minimal power
is required too.

5.2 Disinfection

Beware:
All components being disinfected must
be washed thoroughly and be free of any food
residues.
The drawings
A
to
I
for the disinfecting process
can be found on the unfolded page.
1. Remove the measuring jug
(Fig.
).
A
2. Using the jug
9
measure 70ml of tap water
and pour into the base
N.B.:
70 ml corresponds to two beakers full
of water (2x 35ml).
3. Place the steam receptacle
(Fig.
).
B
4. Place the bottle holder
tacle (Fig.
).
C
Beware:
Always disinfect the bottles open and
dismantled, otherwise the material can become
misshapen.
5. Place the open bottles in the holder
6. Place the accessories basket
7. Lay the accessories in the basket
8. Place the lid
9. Insert the mains plug into a suitable socket.
10.Switch the device on using the On switch
The steam steriliser will switch off automatically
after disinfecting and the control light will go
out.
from the base
9
6
6
(Fig.
A
).
Beware!
socket after each use to ensure that the device
on the base
5
6
cannot be inadvertently switched on.

5.3 Please observe the following:

in the steam recep-
4
17
D
).
N.B.:
Stack the lids if possible in the holder
4
. This will save space in the accessories
basket (Fig.
E
).
steam receptacle (Fig.
).
F
1
on top of the basket
H
).
If the control light
N.B.:
8
means the On switch
7
inadvertently activated.
The control light
8
will light up (Fig.
Warning!
Directly after switching off, the device
will still contain steam, which will, to
some extent, escape through the
steam outlet valve. You should there-
fore take care not to scald yourself.
Allow the equipment to cool down
while sealed for at least three minutes.
Directly after disinfecting the bottles
will be very hot and should only be
removed using the tongs supplied.
The plug should be removed from the
The disinfection process lasts approx.
8 minutes using 70 ml of water.
Disinfection is only guaranteed if the
process is not interrupted and the time is
not reduced.
4
(Fig.
on top of the
3
(Fig.
).
3
G
3
(Fig.
is already lit, this
has already been
7
.
I
).

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

10.251.01210.749.054

Tabla de contenido