Manual Mode; Automatic Mode; Remote Input; Technical Specifications - Honeywell Home FP134 Guia De Instalacion

Operation
3
NOTE: If the "setback" and "off" orders recieved by a heating unit are reversed,
reverse th "Ph" and the "N" wires on the heating unit.
3.1

Manual mode

Transmits the order selected via one of the order
buttons. To use this mode:
1 Select the zone by pressing the Zone button.
(Press for 3 seconds to select all 3 zones.)
2 Select the manual (Man) mode by pressing
the Man/Auto button.
3 Select the order by pressing the appropriate
order button.
3.3

Remote input

Whenever an order is received via the remote input, it becomes the active
order for all 3 zones. To know which orders can be initiated by the energy
manager, the phone controller or the home automation system, see the
table on page 4. The is displayed when signals are received via the
remote input.
Bypass
Orders received via the remote input have priority over orders initiated via
the programmer. However, you can bypass the remote input order for each
zone for 2 hours. At the end of the 2 hours, the remote input order becomes
active again.
1 Select the zone using the Zone button.
(Press for 3 seconds to select all 3 zones.)
2 Press the desired order button.
The icon flashes during the bypass.
Schedule customization
5
Use the following procedure to select the order and the start time for each
of the 4 programs for each zone. The settings of each program will be the
same for each day. However, you can then select which programs to be
executed for each day and for each zone.
1 Press the PGM to start programming.
2 Select the zone using the Zone button.
(Press for 3 seconds to select all 3 zones.)
3 Select the program using the PGM button.
4 Set the program start time.
5 Select the mode by pressing the corresponding button.
6 Repeat steps 3 to 5 for the remaining programs for
the selected zone.
7 Go to step 2 if you wish to select another zone.
8
8 Press to exit programming.

Technical Specifications

6
Model: FP134
Power supply: 230 VCA /50 Hz
Consumption: 25 mA maximum
Pilot wire output: 60 mA per output ?230 VCA
Maximum load: 10 units per pilot wire output (FP)
Operating Temperature: 0 - 50ºC
Storage temperature: -20 - 50ºC
Protection: Class 2
Protection index: IP20
Automatic action: 1Y type
Environment: Normally polluted
Software: Class A
Memory type: Program settings are permanently saved time settings
are saved for 4 hours during power outage
Remote input: Universal relay (230 VCA/500 μA) or pilot wire
Wire thickness: 0,32 - 2,1 mm
2
3.2
The orders are sent to each zone according to the schedule
programmed for that zone. To use this mode:
1 Select the zone by pressing the Zone button.
2 Select the Auto mode by pressing the
Bypass
You can bypass the automatic mode for 2 hours. At the end of the 2 hours,
the programmer returns to the automatic mode.
1 Select the zone using the Zone button.
R ƒ T
2 Press the desired order button.
The auto mode icon flashes during the bypass.
The same schedule is used by default for all 3 zones as shown below.
R ƒ T
1. Comfort (C), 3.5ºC setback (S)
When selecting the number of programs:
1 Press the MAN/AUTO button for 3 seconds
2 Select the zone using the ZONE button.
3 Press MAN/AUTO until the desired day is displayed.
4 Set the number of programs for the selected day
R ƒ T
NOTE: If no program is selected for a particular day, FP134 uses the
order of the last progarm until the start of the next program
5 Repeat steps 3 and 4 for the each remaining day.
6 Go to step 2 if you wish to select another zone.
7 Press
Bk-electronic GmbH
Hardhofweg 40
74821 Mosbach
Germany
For assistance with this product please visit
livewell.honeywellhome.com

Automatic mode

(Press for 3 seconds to select all 3 zones.)
Man/Auto button.
(Press for 3 seconds to select all 3 zones.)
Preprogrammed Schedule
4
Wake-up time Leave for work
Every Day Monday to Friday
Zone pgm Time Order Mon
1
1 6:00 C
ü
2 8:30 S
ü
A
3 17:00 C ü
4 23:00 S ü
Number of programs per day: 4
until PPd is displayed.
(Press for 3 sec. to select all 3 zones.)
using the buttons. The options are:
• 4 (to select all 4 programs)
• 2 (to select program 1 and 4 only)
• 0 (no program is selected for that day)
8
to exit.
R ƒ T
Return home Sleep time
Monday to Friday Every day
Tue Wed Thu Fri Sat Sun
ü ü ü ü ü
ü ü ü ü
ü ü ü ü
ü ü ü ü ü
4 4 4 4 2
© 2019 Resideo Technologies, Inc.
This product manufactured by Resideo and its affiliates.
The Honeywell Home trademark is used under license
from Honeywell International Inc. All rights reserved.
33-00051-02
ü
ü
2