Yamaha XDA-QS5400RK Manual De Instrucciones página 13

Tab Menu Item
Basic Settings Output Select
AMP1 (2/3/4)
BTL1 (2/3/4)
AMP/BTL Trim
Preout Trim
Input Trim
Auto Power
Standby
Network
Standby
Chime1 (2/3/4)
Chime Volume
Chime1 (2/3/4)
Sound
Chime1 (2/3/4)
Test
CUT IN
CUT IN Power
On
CUT IN Mode
CUT IN Trim
CUT IN Input
Sense
Setting values Default
Zone1 / Zone2 / AMP1-Zone1,
Zone3 / Zone4 / AMP2-Zone2,
None AMP3-Zone3,
AMP4-Zone4
– –
-10.0 to +10.0dB 0.0dB
(0.5dB Steps)
-10.0 to +10.0dB 0.0dB
(0.5dB Steps)
-6.0 to +6.0dB 0.0dB
(0.5dB Steps)
Off / 5 min / 20 U.K. and
min / 2 Hr / 4 Hr / Europe models
8 Hr / 12 Hr : 20 min
Other models :
Off
Off / On / Auto Auto
Off / On Off
Mute, -80.0 to -30.0dB
0.0dB
(0.5dB Steps)
(Sounds) –
– –
Off / On Off
Disable / Enable Disable
Fade / Fade
Cut - 5sec /
Cut - 10sec /
Cut - 30sec /
Cut - 1min /
Cut - 5min
-30.0 to +30.0dB 0.0dB
(0.5dB Steps)
Low / Mid / High Mid
Explanation
Sets the zone as the audio output in each channel.
Displays normal/bridge connection of speakers.
Corrects volume difference between each channel and
the standard output signal.
Corrects volume difference between each preout signal
in each Zone.
Compensates for volume differences between input
sources.
Automatically sets the unit to standby mode when there
are no operations for a specified amount of time.
When this is set to 5 min or 20 min, the unit will only be
set to standby mode automatically if there is no input
signal during the 5 or 20 minutes without any
operations.
Enables/disables the feature allowing the Zone to be turned
on by network devices (Network Standby). When this is
"Auto", Network power will turn off when the main power is
off and the unit continues not to be linked to network
devices.
Enables/disables the feature allowing the preset chime
to sound in each Zone when the + and -of the CHIME 1
(/2/3/4) jack are shorted.
Note
If this function is enabled, the unit's standby power
consumption increases to output audio immediately.
Adjusts the chime volume in each Zone.
Sets the preset chime for the CHIME 1 (/2/3/4).
Tests the preset chime sound for the CHIME 1
(/2/3/4).
Enables/disables the Cut in/Fade function in each Zone.
Enables/disables the feature allowing the Zone to be
turned on by the CUT IN input in each zone.
Note
If all Zones are turned off (standby) and this function is
enabled, the unit's power consumption increases to
output audio immediately.
Sets whether the audio signals from the CUT IN jacks
fade in or cut in the playback.
"Fade": mixes the audio signals from the CUT IN jacks
into the lowered playback. The unit will be set to the
previous playback automatically if there is no CUT IN
signal for 3 seconds.
"Cut": mutes the playback and outputs the audio signals
from the CUT IN jacks instead. The unit will be set to
the previous playback automatically if there is no CUT
IN signal for 5 seconds to 5 minutes.
Adjust the volume difference between the CUT IN input
and the standard output signal.
Note
If this is set to a high level, the sound may become
clipped when the master volume level is high.
It is recommended to set CUT IN Trim to a level at
which there is no clipping at the desired master volume
levels.
Sets the sensitivity for audio input signal level of the
CUT IN jacks.
"Low": lowers the sensitivity and reacts to only loud
sound.
"High": heightens the sensitivity and reacts to even
small sound.
EN
En 13