Technical Specifications - Toolland WPST3 Manual Del Usuario

6. Assembly
 Insert the column [2] into the base [1] and tighten it securely with the screw(s) [a].
 Slide the stop [3] over the column.
 Slide the drill holder [4] over the column [2].
 Slide the washer and lever [5] over the bolt and use this to secure the drill holder [4] to the column [2].
Use the included hex key.
 Lift the lever [5] and the lever support [6]. Align the holes and insert the bolt [e].
Note: the bolt must be inserted at the side of the lever support [6].
 Place a washer over the bolt [e] and tighten the lock nut.
 The drill holder [4] has a provision to store the hex key.
7. Use
 Inspect the drill stand for signs of damage before every use. When damage is noticed, do not use it.
Contact your local dealer for repair and/or spare parts.
 Keep the working area clean at all times.
 Place the drill stand on a flat and steady surface capable of carrying the weight of the stand and the work
piece. Do not use on slopes etc. ...
 For security reasons, it is highly recommended to attach the drill stand to the work bench. Screw 4 screws
(not incl.) through the 4 corners of the base [1].
 Mark the location of the holes on the work piece.
 Place a drill (not incl.) with the desired drill bit (not incl.) in the drill holder [4] and tighten the bolt [d] and
nut. When necessary, use the included plastic reduction ring. Hold the drill holder [4] with one hand to
avoid that it slides down possibly causing damage to the drill bit when it hits the base [1]. Do not switch on
the drill yet.
 Pull down the lever [5] and slide down the drill holder until the tip of the drill bit almost touches the base
[1] Slide the stop [3] upwards until it touches the drill holder [4] and secure it tightly with bolt [b]. This
prevents that the drill bit accidentally hits the base during drilling.
 Place the work piece on the base [1], align the drill bit with a hole marking and secure the work piece in
such a way that it can not accidentally move during drilling (securing equipment not included).
Note: Make sure the drill is always above the base [1] when drilling holes.
 Lower the drill holder [4] until the tip of the drill bit almost touches the work piece. Tighten the drill holder
[4] securely with bolt [c].
 Make sure all bolts are securely tightened before proceeding!
 Switch on the drill.
 When the drill is at full speed, gently pull down the lever [5]. Depending on the material of the work piece
and the diameter of the drill bit, apply some cooling liquid (not incl.) on the drill bit.
 When the desired depth is reached (see ruler [8]), gently lift the lever [5] until the drill bit is completely
out of the hole. Never let go off the lever as this will cause damage to the mechanism.
 Switch off the drill and wait until the drill bit comes to a full stop before handling the work piece.
 When multiple holes of the same depth are required, use the preset stop. Release the preset bolt [7] on the
side of the drill holder [4]. Refer to illustration [C].
 Drill the hole as described before. When the desired depth is reached, tighten the preset bolt [7]. For the
following holes, simply pull down the lever [5] until it will not move any further.
8.

Technical Specifications

column height
column-to-drill centre
max. drill depth
weight
Use this device with original accessories only. Velleman nv cannot be held responsible in the event
of damage or injury resulting from (incorrect) use of this device. For more info concerning this
product and the latest version of this manual, please visit our website www.toolland.eu. The
information in this manual is subject to change without prior notice.
© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman nv. All worldwide rights reserved. No part of this
manual may be copied, reproduced, translated or reduced to any electronic medium or otherwise without the
prior written consent of the copyright holder.
V. 02 – 08/08/2016
WPST3/WPST4
WPST3
400 mm
105 mm
60 mm
± 1500 g
4
WPST4
510 mm
± 3300 g
©Velleman nv