Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Power Dome
400 by Wagan Tech
™
BATTERY STATUS
Battery Status provides the user with a current state of charge on the internal
battery. It is the user's responsibility to periodically monitor the battery charge and
to recharge the battery after each use. Recharge every three months even if the
Power Dome has not been used.
1. Press and hold the Battery Status button.
2. The Charge Level Indicator (DC Voltmeter) will display the battery voltage.
3. Battery status (voltage) is read with charging adapters disconnected.
•
≥12.6V DC: battery is ready for use
•
≤12.0V DC: battery needs some charging
•
<10.5V DC: battery is discharged, charge immediately
CHARGING THE POWER DOME
AC CHARGING
Make sure the supplied AC Charging Adapter is to be powered by the correct
voltage (i.e. 110V AC or 220V AC). Only use the AC charging adapter supplied
with this unit.
1. Make sure all Power Dome switches are set to off.
2. Open the dust cover on the Charging Jack.
3. Connect the AC Charging Adapter to the AC outlet.
4. Plug the Charging Adapter's cord into the Power Dome's Charging Jack.
5. The Charging Indicator will light during the charging process.
6. Charge for a full 36 hours before initial use. (Power Dome can be charged
continuously via AC adapter without damaging the internal battery.)
7. After charging the battery, disconnect the adapter from the AC outlet first,
then from the charging jack.
8. Replace the dust cover on the charging jack.
NOTE: The Charging Indicator light indicates charging. Press the Charge
Status Button for the Voltmeter to show battery voltage and charge status.
DC CHARGING IN YOUR VEHICLE OR BOAT
Only use the DC charging adapter supplied with this unit.
NOTE: The engine must be running while charging the Power Dome.
1. Make sure all Power Dome switches are set to off.
www.wagan.com
3
®
User's Manual—Read before using this equipment
2. Open the dust cover on the Charging Jack.
3. Plug the Charging Adapter's cord into the Power Dome's Charging Jack.
4. Plug the DC Charging Adapter into an accessory outlet (cigarette lighter).
5. The Charging Indicator will light during the charging process.
6. Do not charge more than 12 hours using the DC method.
7. After charging the battery, disconnect the adapter from the accessory
socket first, then from the charging jack.
8. Replace the dust cover on the charging jack.
DC POWER PORT
DC Power Ports (accessory sockets) are located under the Pressure Gauge and
the Battery Status Meter (voltmeter). The ports can power a DC load of up to 11
Amps. Overloading the port will result in "tripping" (a self-resetting circuit breaker).
Removing the overload automatically restores power to the DC Power Ports.
1. Uncover the dust cover from the Power Port.
2. Insert the 12V DC accessory plug into the Power Port.
3. Operate the appliance as you normally would.
4. After use, disconnect the accessory plug from the Power Port.
5. Replace the Power Port's dust cover.
6. Recharge the Power Dome as soon as convenient.
USING THE AIR COMPRESSOR
The Air Compressor Gauge and Power Switch are located on the front of the
Power Dome. The Compressor Air Hose Compartment is located on the rear of the
Power Dome.
CAUTION:
• Never connect or disconnect the nozzle with the compressor operating.
• Before any tire inflation, look for the recommended inflation pressure
information on the sidewall of the tire.
INFLATION PROCEDURE
1. Open the Air Hose Compartment door at the rear of the Power Dome and
extend the air hose.
2. Position the Power Dome so that you see the front panel.
©2012 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks used by Wagan Corporation.
4
Publicidad
Tabla de contenido
