Troubleshooting - SOLAC SW8230 Instrucciones De Uso

liquid and then dry.
- Do not use solvents, or products with an acid or base pH such as
bleach, or abrasive products, for cleaning the appliance.
- Do not let water or any other liquid get into the air vents to avoid dam-
age to the inner parts of the appliance.
- Never submerge the appliance in water or any other liquid or place it
under running water.
Supplies
- Supplies can be acquired from distributors and authorised establish-
ments (such as filters, etc.) for your appliance model.
- Only the following type of supplies must be used with the appliance.
- Lamp type: E14, Max: 15 W
- These supplies are available in specialist shops.
Anomalies and repair
- In case of breakdown call the customer, service telephone number
indicated in the guarantee sheet. Do not attempt to disassemble or
repair the appliance yourself as this may be dangerous.
For EU product versions and/or in case that it is requested in your
country:
Ecology and recyclability of the product
- The materials of which the packaging of this appliance consists are
included in a collection, classification and recycling system. Should
you wish to dispose of them, use the appropriate public recycling bins
for each type of material.
- The product does not contain concentrations of substances that could
be considered harmful to the environment.
This symbol means that in case you wish to dispose of the
product once its working life has ended, take it to an authorised
waste agent for the selective collection of Waste from Electric
and Electronic Equipment (WEEE).
This appliance complies with Directive 2014/35/EU on Low Voltage, Di-
rective 2014/30/EU on Electromagnetic Compatibility, Directive 2011/65/
EU on the restrictions of the use of certain hazardous substances in
electrical and electronic equipment and Directive 2009/125/EC on the
ecodesign requirements for energy-related products.

TROUBLESHOOTING:

Problem Reason
No pow-
er or the
Adapter power is not
machine
properly connected
runs
slowly
Needle eye not in the
middle
Skipping
Needle bent
stitches
Presser foot too loose
Lower thread has been
Bobbin
used up
thread
cannot
Needle threaded
be drawn
incorrectly
up
Thread blocked by
lower bobbin
Thread
Needle scarf too rough
keeps
breaking
Needle shank not seat-
ed in the upper end
Thread tension dial,
thread guide or thread
pulling bar is rough
Thread blocked by
upper bobbin spool
Stitch-
Upper thread too loose
es too
or tight
loose or
uneven
Needle bent
Threading incorrect
Presser foot and/or
needle is loose
Pull fabric with force
when sewing
Needle
Needle not lowered
breaks
into fabric when start
sewing
The needle is in the
fabric when adjust the
pattern selection dial
Solution
Correct connect adaptor.
Replace with a new adaptor
Remove and re-insert the
needle with the flat side of the
needle to the back.
Remove and re-insert a new
needle.
Tighten the presser foot ac-
cording to installation instruc-
tion above mentioned.
Replace with new full bobbin
Re-thread the needle, making
sure it is threaded from the
front to the back.
Correctly thread the upper
thread and lower thread again
according to instruction above
mentioned.
Remove and re-insert a new
needle.
Insert the needle correctly
Polish with fine sand paper
Pull out the spool pin and
make the bobbin or thread run
smoothly
Adjust thread tension dial and
make the stitches sew evenly
Remove and re-insert a new
needle
Check and thread again
Remove and re-insert a new
needle, and tightly fix presser
foot and needle
Remove and re-insert a new
needle and tightly fix it. After
that thread machine, again.
Remove and re-insert a new
needle and tightly fix it, thread
again, turn the hand wheel to
lower the needle into fabric,
and then start sewing
Remove and re-insert a new
needle and tightly fix it