Optional Accessories - RED CASTLE RC 2 Instrucciones De Uso

Lift up the lever located at the rear of the car
seat and choose the position best suited to your
baby's weight:
4 POSITIONS
Position A
1
Lying
Position B
2
Reclining
Position C
3
Semi-reclining (*)
Position D
4
Traditional
NB: When not used in the car, all 4 positions are
possible on the stroller up to 9kgs.
(*) IMPORTANT: the position C (semi-reclining)
is not authorized in a vehicle unless the car seat
is installed on the Primafix base.
Handle positions (fig. 18):
There are 3 handle positions.
To change position, release the handle position
by pushing down simultaneously on the buttons
at either side (fig. 17) while at the same time
moving the handle forwards or backwards, to
the required position (« click » heard).
1a -> Position when used in the car
1b -> Position when carrying baby
1c -> Position when used as a rocking chair /
on the stroller
IMPORTANT: Remain vigilant at all times! - If
you carry baby in his RC 2 car seat outside of
the vehicle, check that the handle is firmly
enclenched in position 1b.
IMPORTANT: Attach your child in all circumstances,
always use the restraining system.
IMPORTANT: To change the handle position from
1b to 1c or 1c to 1b, the hood must always be
unfolded (fig. 1).

Optional accessories

Attaching the Hood:
• To attach the hood: Insert the plastic
attachments located either side of the hood into
the side sockets of the RC 2 car seat (fig. 19).
• Line up the openings, indicated by the blue
arrows (located at the rear of the hood), with
the guides for the car seat belts (fig. 20 and 21).
up to 5kg (fig.13)
up to 5kg (fig.14)
from 5kg to 10kg (fig.15)
from 5kg to 10kg (fig.16)
• Adjust the hood as required in order to protect
your baby from the sun.
• To remove the hood : push down on the plastic
attachments at either side of the hood, at the
same time pulling the end of the hood upwards.
Attaching the apron:
• Before attaching the apron, attach the hood
(see previous chapter).
• Cover the RC 2 car seat with the apron (fig. 22).
• Match the velcro straps and the press studs of the
apron and the hood with those on the car seat
cover. Press them firmly to close them. (fig. 23).
• To remove the apron, detach the velcro and
undo the press studs.
Do not use the RC 2 car seat apron in the
vehicle. In the case of an emergency, this could
impede access to the child.
Attaching the sun screen
• Position the wider part (shown at the top of
fig. 24) onto the hood and attach the velcros.
• Pull the sun screen taut towards the lower part
of the seat and attach the velcros (fig. 25).
IMPORTANT: The sun screen has been designed
to reduce the sun's glare and limit the effect
of UV rays. The use of this sun screen does
not exempt you from the need to protect your
child. We recommend the systematic use of a
sun cream. Regularly check that the child has
enough to drink.
Care and washing instructions
• The car seat and the safety harness can be
wiped clean with warm, soapy water.
• To remove the seat cover: open the harness
buckle (fig. 26), slip the harness straps and
the buckle through the slots in the seat cover
(fig. 27). First remove the front part of the
seat cover then undo the press stud at the top
of the seat back. (fig. 28).
• To replace it, make sure that the safety
harness and the edges of the cover are
positioned correctly.
• Wash the cover of the car seat in warm,
soapy water (do not machine wash). Rinse
thoroughly and leave open to dry. Do not iron.
Do not use abrasive cleaning products.
GB
19