Taurus ALPATEC AC 260 KT Manual Del Usuario página 24

- Press Up or Down to adjust temperature in a
range of 17ºC~30ºC.
- When the up or down is pressed once,
temperature will go up or down by 1ºC every time.
- Press speed to select high, mid or low fan speed.
Fan mode:
- Press mode to select fan mode fan indicator
turns on.
- Press speed to select high, mid or low speeds.
- In that mode, press Speed for 5 seconds to
run the internal dry function, i.e. both upper and
lower fans work simultaneously. Press Speed
for another 5 seconds to cancel the internal dry
function.
- Temperature is not adjustable.
- Press Swing to turn off or turn on the up/down
swing function.
Dehumidifying mode:
- Press "MODE" to select dehumidifying mode,
dehumidifying mode indicator turns on.
- Remove the plug of drainage cap, insert a tube
and put the other side of the tube into water
containers or drain channels.
- When entering dehumidification mode, if the
room temperatures is ≥15ºC, the compressor will
start to work.
- If the room temperature is ≤13ºC, compressor
stops; when the temperature rises back to ≥15ºC,
the compressor restarts (the compressor shall
meet the 3-minute delay protection function).
- In dehumidification mode, the fan run in low
speed by default, and the wind speed are not
adjustable. ·Temperature cannot be set.
NOTE: When the dehumidification function is in
use, the exhaust pipe assembly shall be removed;
otherwise it will lead to not obvious dehumidification
effect or display "FL" water full alarm.
Automatic mode:
- Select automatic mode by pressing mode button
or via remote controller and automation indicator
light is on.
- After selecting the automatic mode, it decides
running state based on ambient temperature:
When the ambient temperature is higher than
25°C, the running mode is the refrigeration mode;
when the ambient temperature is lower than 25°C,
the running mode is the fan only mode.
Compressor protection:
- Three minutes later after power on / restart,
compressor starts to run.
Notice AC 260 KT.indb 24
Water tank full protection:
- When the water level in the bottom water plate
is above the warning level, the unit will alert
automatically a.
-Please discharge water in the machine according
to chapter "water drainage".
Water drainage:
- When the inner water tank is full, its indicator will
flash on the screen.
- The appliance enters into standby mode.
- Pull out the plug to drain out water, power off
the machine and restart it , the machine will runs
normally .
-This model have self evaporative function,
under cooling mode, please do not use continue
drainage to get better cooling effect.
Once you have finished using the appliance:
- Turn the appliance off, using the on/off switch.
- Unplug the appliance from the mains.
Cleaning
- Disconnect the appliance from the mains and
allow it to cool before undertaking any cleaning
task.
- Clean the electrical equipment and the mains
connection with a damp cloth and dry. DO NOT
IMMERSE IN WATER OR ANY OTHER LIQUID.
- Clean the equipment with a damp cloth with a
few drops of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or
base pH such as bleach, or abrasive products, for
cleaning the appliance.
- Never submerge the appliance in water or any
other liquid or place it under running water.
- If the appliance is not in good condition of
cleanliness, its surface may degrade and
inexorably affect the duration of the appliance's
useful life and could become unsafe to use.
Air filter cleaning:
- Clean the air filters every 2 weeks. If the air filter
is blocked with dust, the efficiency will reduce.
- Pull out up and down filter as below pictures
- Wash the air filters by immersing it gently into
warm water with a neutral detergent, rinse it and
dry it thoroughly in a shaded place.
- Install air filters carefully after cleaning the filters.
After Season Maintenance:
- Pull out the plug in drainage hole and empty the
18/02/2016 19:11