Makita 9227CB Manual De Instrucciones página 6

ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing loop handle
Always install the loop handle on the tool before opera-
tion. Hold the tool's switch handle and the loop handle
firmly with both hands during operation.
Install the loop handle so that its protrusion will fit into the
matching hole in the gear housing. (Fig. 4)
Install the bolts and tighten them with the hex wrench.
The loop handle can be installed in two different direc-
tions as shown in Fig. 5 & 6 whichever is convenient for
your work.
Installing or removing wool pad (Fig. 7)
To install the wool pad, first remove all dirt or foreign mat-
ter from the backing pad. Press the shaft lock and screw
the backing pad onto the spindle. Insert the sleeve 18
into the center hole of the backing pad. Using the sleeve
18 as a positioning guide, install the wool pad on the
backing pad with the sleeve 18 inserted through the cen-
ter hole of the wool pad. Then remove the sleeve 18 from
the backing pad.
To remove the wool pad, just tear it off the backing pad.
Then unscrew the backing pad while pressing the shaft
lock.
OPERATION
Polishing operation (Fig. 8)
CAUTION:
• Always wear safety glasses or a face shield during
operation.
Hold the tool firmly. Turn the tool on and then apply the
wool bonnet to the workpiece.
In general, keep the wool bonnet at an angle of about
15 degrees to the workpiece surface.
Apply slight pressure only. Excessive pressure will result
in poor performance and premature wear to wool bonnet.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
Replacement of carbon brushes (Fig. 9 & 10)
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
6
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Sponge pad (Hook & loop)
• Backing pad 165 (Hook & loop)
• Wool bonnet 180
• Sleeve 18
• Side grip (auxiliary handle)
• Loop handle
• Head cover
• Wool pad 180 (Hook & loop)
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode: polishing
Vibration emission (a
Uncertainty (K): 1.5 m/s
If the tool is used for other applications, the vibration
emission value may be different.
• The declared vibration emission value has been mea-
sured in accordance with the standard test method and
may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the oper-
ator that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to
the trigger time).
): 83 dB (A)
pA
): 94 dB (A)
WA
): 6.0 m/s 2
h,P
2
ENG102-3
ENG209-3
ENG901-1