Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
INSTALLATION AND MAINTENANCE INSTRUCTIONS
CZ-6
Six Zone Interface Module
SPECIFICATIONS
Normal Operating Voltage:
Stand-By Current:
Alarm Current:
Temperature Range:
Humidity:
Dimensions:
Accessories:
Wire Gauge:
Maximum IDC Wiring Resistance:
External Supply Voltage
DC Voltage:
Ripple Voltage:
Current:
IDC:
BEFORE INSTALLING
This information is included as a quick reference installation
guide. Refer to the appropriate control panel installation manual
for detailed system information. If the modules will be installed
in an existing operational system, inform the operator and local
authority that the system will be temporarily out of service.
Disconnect the power to the control panel before installing the
modules. This system contains static sensitive components.
Always ground yourself with a proper wrist strap before handling
any circuits so that static charges are removed from the body. The
module housing should also be grounded.
NOTICE: This manual should be left with the owner/user
of this equipment.
D500-67-00
15-32 VDC
2 mA
40 mA (assumes all six LEDs solid on)
0°C to 49°C
10 to 85% Non condensing
17.3cm H x 14.7cm W x 3.2cm D
Suitably grounded metallic cabinet
0.9mm
2
-3.25mm
2
25 Ohms
18-28 volts power limited
0.1 volts RMS maximum
90mA per module
Supervised and power limited
Compatible Two-wire System Sensor Smoke Detectors for use with CZ-6
DET.
DETECTOR
MODEL
DET. ID
MANUFACTURER
1151
A
SYSTEM SENSOR
1451
A
SYSTEM SENSOR
1451DH
A
SYSTEM SENSOR
2151
A
SYSTEM SENSOR
2451
A
SYSTEM SENSOR
2451TH
A
SYSTEM SENSOR
5451
A
SYSTEM SENSOR
1100
A
SYSTEM SENSOR
1400
A
SYSTEM SENSOR
**2100AT
A
SYSTEM SENSOR
2100B
A
SYSTEM SENSOR
2100D
A
SYSTEM SENSOR
2100S
A
SYSTEM SENSOR
2100TB
A
SYSTEM SENSOR
2100TD
A
SYSTEM SENSOR
2100TS
A
SYSTEM SENSOR
2300B
A
SYSTEM SENSOR
2300TB
A
SYSTEM SENSOR
2400
A
SYSTEM SENSOR
2400TH
A
SYSTEM SENSOR
* 2W-B
A
SYSTEM SENSOR
*2W-TB
A
SYSTEM SENSOR
DH100LP
A
SYSTEM SENSOR
* Class B, Style B only
** No Accessory will be supported by 2100AT
GENERAL DESCRIPTION
The CZ-6 Six Zone Interface Module is intended for use in an
intelligent alarm system. Each module provides an interface
between the intelligent alarm system and a conventional alarm
system loop. A common SLC input is used for all modules, and
the initiating device loops share a common supervisory supply
and ground. Otherwise, each monitor operates independently
from the others. Each module has its own unique address.
A pair of rotary code switches is used to set the address of the
first module from 01 to 94. The remaining modules are automati-
cally assigned to the next five higher addresses. Provisions are
included for disabling a maximum of two unused modules to
release the addresses to be used elsewhere. Each module also has
panel controlled by color LED indicators. The panel can cause the
LEDs to blink, latch on, or latch off.
BASE MODEL
B110LP, B401
B401, B401B
DH400
B110LP, B401
DH400, B401B, B401
B401, B401B
B401
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
1
Pittway Technologica S.p.A
Via Caboto 19/3
34147 Trieste, Italy
MAX DET.
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
I56-2256-01
Publicidad
Tabla de contenido
Manuales relacionados para System Sensor CZ-6
Resumen de contenidos para System Sensor CZ-6
- Página 1 GENERAL DESCRIPTION This information is included as a quick reference installation The CZ-6 Six Zone Interface Module is intended for use in an guide. Refer to the appropriate control panel installation manual intelligent alarm system. Each module provides an interface for detailed system information.
- Página 2 INSTALL DETECTORS PER MANUFACTURER'S INSTALLATION INSTRUCTIONS. Figure 1: Interface two-wire conventional detectors. 1. To use a common power supply between multiple CZ-6 modules, connect a long power supply jumper from T5 or T6 to T5 or T6 on the adjacent CZ-6 module.
- Página 3 PCB 1 PCB 2 — EXTERNAL POWER SUPPLY VIEW A-A Figure 2 Figure 2: Example of multiple boards sharing same external supply. Refer to figure 2 for typical wiring. Make certain lip on long power supply jumper engages retaining tab on T5 or T6 as shown in View A-A. D500-67-00 I56-2256-01...
- Página 4 LED bicolore controllati dal pannello. A seconda delle all’utente di questo apparecchio. istruzioni del pannello, i LED possono lampeggiare, essere attivati oppure disattivati. Rilevatori di fumo System Sensor a due fili compatibili per l’uso con il modulo CZ-6 MODELLO PRODUTTORE DEL RILEV.
- Página 5 TWISTED PAIR. Figura 1 : Tradizionali rilevatori a due fili di interfaccia 1. Per utilizzare un’alimentazione tradizionale tra più moduli CZ-6, collegare un jumper di alimentazione lungo da T5 o T6 a T5 o T6 sul modulo CZ-6 adiacente. D500-67-00 I56-2256-01...
- Página 6 PCB 1 PCB 2 — FONTE DI ALIMENT AZIONE ESTERNA Figura 2 VISTA A-A Figura 2: Esempio di più schede che condividono la stessa alimentazione esterna. Per informazioni sul cablaggio tipico, ved. figure 7 e 8. Verificare che la piegatura del bordo sul jumper di alimentazione lungo si agganci alla linguetta di fissaggio su T5 o T6 come mostrato nella vista A-A.
-
Página 7: Módulo Interfaz De Seis Zonas Convencionales
LEDs parpadeen, se mantengan iluminados de forma fija o se su uso en un sistema de alarma inteligente. Cada módulo apaguen. proporciona interconexión entre el sistema de alarma inteligente Detectores de Humo de dos hilos de System Sensor compatibles con CZ-6 DET. DETECTOR MODELO ID del DET. -
Página 8: Piezas Incluidas
INSTALE LOS DETECTORES SEGÚN LAS INDICACIONES DEL FABRICANTE. Figure 1: Detectores convencionales de dos hilos 1. Si desea utilizar una fuente de alimentación común entre varios módulos CZ-6, conecte un puente de alimentación desde T5 o T6 a T5 o T6 del módulo CZ-6 adyacente. - Página 9 PCB 1 PCB 2 — FUENTE DE ALIMENTACIÓN EXTERNA Figure 2 VISTA A-A Figura 2: Ejemplo de varias tarjetas con una misma fuente de alimentación externa y rearmable. Las conexiones del cableado típico se muestran en la figura 1. Asegúrese de que la pestaña del puente de alimentación engancha con la pestaña de sujeción en T5 o T6 como se muestra en la Vista A-A.
-
Página 10: Vor Der Installation
Zentrale gesteuerte, zweifarbige LED-Anzeige. Die ALLGEMEINES Zentrale kann die LED blinkend, folgend ein oder folgend aus Das CZ-6 Gruppenmodul wird in intelligenten ansteuern. Gefahrenmeldeanlagen eingesetzt. Jedes Modul verfügt Kompatible Zwei-Draht Sensor Rauchmelder für das CZ-6 Modul MELDER MELDER MODEL MEL. ID HERSTELLERSOCKEL MODELL MAX MELDERANZ. - Página 11 INSTALLIEREN SIE DIE MELDER GEMÄß DEN HERSTELLERVORGABEN DER INSTALLATIONSANLEITUNG Abbildung 1. Um eine gemeinsame Spannungsversorgung für mehrere CZ-6 Module einzusetzen, schliessen Sie das Steckkabel zur Spannungsversorgung von T5 oder T6 an T5 oder T6 des benachbarten CZ-6 Modules an. D500-67-00 I56-2256-01...
- Página 12 SPANNUNGSVERSORGUNG DARSTELLUNG A-A Abbildung 2: Beispiel zur gemeinsamen Spannungsversorgung mehrerer Module. Vergewissern Sie sich, dass der Stecker des Spannungskabels, wie in der Darstellung A-A gezeigt, fest in den Halteclip von T5 oder T6 einrastet. D500-67-00 I56-2256-01 © 2003 System Sensor...