Operation - EINHELL GE-CR 30 Li Manual De Instrucciones

Ocultar thumbs Ver también para GE-CR 30 Li:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

6. Operation

Caution!
The device is equipped with a safety switch to
prevent unauthorized use. Immediately before
using the equipment, insert the safety plug (Fig.
13/Item 5). Remove the safety plug again when
interrupting or terminating your work. To do so,
press the lug (Fig. 13/Item 17).
Danger! In order to prevent the equipment from
being switched on unintentionally it comes with
a two-point switch (Fig. 14/Item 18) on the push
bar which has to be pressed before the selector
lever (Fig. 14/Item 19) can be pressed. If the lever
switch is released, the equipment switches off .
Repeat this process several times so that you are
sure that your equipment
functions properly. Before you perform any repair
or maintenance work on the equipment, ensure
that the cultivator blades are not rotating and that
the safety plug is disconnected.
Before you start any work, the equipment must be
moved into the working position. First, press the
locking pin (Fig. 15/Item 20) in the direction of the
arrow as shown in Fig. 15 and swing the wheel
unit up until the locking pin latches into position.
To convert the equipment to the transport
position, proceed in reverse order.
Always ensure that a safe distance (provided
by the long handles) is maintained between the
machine and the user.
Be especially careful when changing direction on
slopes and inclines. Maintain a solid footing and
wear sturdy, non-slip footwear and long trousers.
Always work along the incline (not up and down).
Use special caution when backing up and pulling
the equipment (tripping hazard)!
Tips for proper working
Place the machine in front of the area you wish to
till and hold it securely on the push bar before you
switch on the machine.
Guide the tiller blades over the area.
To achieve cleanly tilled soil always ensure that
you guide the machine in straight lines wherever
possible.
Insodoing, the aeration swaths should always
overlap each other by a few centimeters in order
to avoid bare strips.
Switch off the motor promptly when you arrive at
the end of the area you wished to till. The motor
must be switched off when you raise the machine
Anl_GE_CR_30_Li_USA_SPK7.indb 13
Anl_GE_CR_30_Li_USA_SPK7.indb 13
EN
(for example to change direction).
Keep the underside of the machine clean and
remove soil deposits. Deposits make it more
diffi cult to start the machine and decrease the
working depth.
Work perpendicular to the slop on inclined areas.
The machine must be switched off and the safety
plug pulled out before you make any checks on
the cultivator blades.
Warning!
The tiller blades will continue to rotate for a few
seconds after the motor is switched off . Never
attempt to manually stop them. In the event
that the rotating tiller blade strikes an object,
immediately switch off the machine and wait for
the tiller blades to come to a complete stop. Then
inspect the condition of the tiller blades. Replace
any parts that are damaged.
6.1 Charging the Li battery pack
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.2 Battery capacity indicator
(Fig. 12 / item 22)
Press the battery capacity indicator switch (23).
The battery capacity indicator (22) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The battery pack has been deep-discharged and
is defective. Do not re-use or charge a defective
battery pack.
- 13 -
24.06.2019 11:08:29
24.06.2019 11:08:29

Publicidad

Tabla de contenido
loading

Tabla de contenido