Descargar Imprimir esta página

BH HI POWER SK G950 Instrucciones De Montaje página 11

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 1
4.- FITTING THE MAIN POST.-
Loosen screws (292) from the top trim cover (273),
Fig.4, insert the protruding cables and the main
post inside the trim cover (273).
Connect terminals (170) and (167), coming out of
the bottom of the main post, with terminals (61)
and (62) coming up from the top of the main body
(01), Fig.4.
Take screws (294) and nuts (295) and taking care
not to pinch the cables, align the main post with
the machine and tighten the screws securely as
shown in Fig.4.
Refit the trim cover (273) removed previously and
the handlebar trim cover (289) and tighten using
screws (337), Fig.4.
5.- FITTING THE FOCUS BARS.-
Right-hand focus bar.-
Position the right-hand focus bar (201) on the
rotation spacer (116), Fig.5.
Connect terminal (204), Fig.5, sticking out of the
bottom of the right-hand focus bar (201), with
terminal (61), coming out of the rotation spacer
(116), Fig.5.
Tighten the right-hand focus bar (201) using
screws (297) along with washers (296), Fig.5,
making sure not to pinch the wires.
Take the two covers (283) and (284), marked on the
inside with the letter (R), and position them where the
focus bar attaches to the rotation spacer, as shown in
Fig.5, tighten using screws (292).
Left-hand focus bar.-
Position the left-hand focus bar (202) on the
rotation spacer (116), Fig.6.
Connect terminal (204), Fig. 6, sticking out of the
bottom of the left-hand focus bar (202), with
terminal (61), coming out of the rotation spacer
(116), Fig.5.
Tighten the left-hand focus bar (202) using screws
(297) along with washers (296), Fig.6, making sure
not to pinch the wires.
Take the two covers (283) and (284), marked on the
inside with the letter (L), and position them where the
focus bar attaches to the rotation spacer, as shown in
Fig.6, tighten using screws (292).
6.- FITTING THE FRONT PROTECTOR.-
Fit the front protector (02) onto the part jutting out
of the main body (01), Fig.7, tighten using screws
(03), Fig.7.
7.- FITTING THE PLATFORM.-
Insert the front end of the platform (290) between
the rear stand and the main body in the direction of
the arrow (01), Fig.8.
8.- LEVELLING.-
Once the unit has been placed into its final position
for doing exercise, make sure that it sits flat on the
SK
LINE
sportkoncept
floor and that it is level. This can be achieved by
screwing the adjustable support blocks (18) up or
down, as shown in Fig.9.
9.- MOVEMENT & STORAGE.-
The appliance is equipped with wheels (41) making
it easier to move about. The two wheels at the front
of the appliance make it easy to store the machine
away, as shown in Fig.10.
10.- PULSE MEASUREMENT.-
Your pulse rate is measured by placing both hands
on pulse sensors (197) located on the handgrips
the handlebar, see Fig.11.
NOTE:
You can also use the chest band (OPTIONAL
TELEMETRIC PULSE SENSOR) to measure your
heart rate.
The reading from the telemetric pulse rate takes
preference over the pulse sensors (197) located on
the handgrips handlebar.
11.- MAINS CONNECTION.-
Make sure that the mains supply voltage is
suitable for the machine before plugging it in.
Connect terminal (g) on the mains cable to terminal
(h) on the machine, Fig.12, the other end of the
mains cable is plugged into a 220V electrical socket.
INSPECTION & MAINTENANCE.-
Switch the unit off and unplug the mains cable.
Use a damp cloth or towel to clean the dust off the
treadmill, especially the side bars and the
electronic console. Do not use solvents.
Use a vacuum cleaner to carefully vacuum around
the visible components (belt, structure, etc.). You
can also vacuum the underside of the unit by
resting it on one of its sides. Similarly, you can
vacuum the inside of the motor housing by
removing the cover that protects the motor (be
careful with the wires).
Periodically check that all of the fastening elements
are duly tightened and connected correctly.
Check and tighten all the parts on your unit
every three months.
Use of this machine with worn parts, e.g. the drive
belt, running belt or rollers, may cause the user
injury. If you are unsure about the condition of any
part, we recommend that you replace it with
original spare parts. The use of other spare parts
may cause injuries or affect the performance of the
machine.
BH RESERVES THE RIGHT TO MODIFY
THE
SPECIFICATIONS
PRODUCTS WITHOUT PRIOR NOTICE.
9
G950
OF
ITS

Publicidad

loading

Productos relacionados para BH HI POWER SK G950